538730
29
Zoom out
Zoom in
Previous page
1/132
Next page
DIL switch 5/DIL switch 65.8.4
SE 2 safety device (closing):
See f Figure 7.5
The functions of the safety device are set with DIL switch 5 in
combination with DIL switch 6.
5 ON Activation kit for closing edge safety device or
photocell with testing
5 OFF
8k2 resistance contact strip•
No safety device (8k2 resistance between •
terminals 20/73, delivery status)
6 ON Brief, delayed reversing in the OPEN direction (for
photocell)
6 OFF
Brief, immediate reversing in the OPEN direction
(for SKS)
5.8.5 DIL switch 7
SE 3 protective device (closing):
See f Figure 7.6
Delayed reversing to CLOSE end-of-travel position.
7 ON Dynamic 2-wire photocell
7 OFF
Static photocell without testing •
No safety device (wire jumper between •
terminals 20/71, delivery status)
DIL switch 8/DIL switch 95.8.6
The functions of the operator (automatic timed closing/
warning phase) and the function of the option relay are set
with DIL switch 8 in combination with DIL switch 9.
See f Figure 7.7a
8 ON 9 ON Operator
Automatic timed closing, advance
warning phase for each gate movement
Option relay
Relay clocks rapidly during the advance
warning phase, normally during the travel
phase and is OFF during the hold-open
phase.
See f Figure 7.7b
8 OFF 9 ON Operator
Automatic timed closing, advance
warning phase only for automatic timed
closing
Option relay
Relay clocks rapidly during the advance
warning phase, normally during the travel
phase and is OFF during the hold-open
phase.
See f Figure 7.7c
8 ON 9 OFF Operator
Advance warning phase for every gate
travel without automatic timed closing
Option relay
Relay clocks rapidly during the
advance warning phase, normally
during the travel phase.
See f Figure 7.7d
8 OFF 9 OFF Operator
No special function
Option relay
Relay picks up in the CLOSE end-of-
travel position.
NOTE:
Automatic timed closing is only possible from the determined
end-of-travel positions (full or partial opening). Automatic
timed closing is deactivated if it fails three times. The operator
must be restarted with an impulse.
DIL switch 105.8.7
Effect of the SE 3 protective device as a through-traffic
photocell with automatic timed closing
See f Figure 7.8
This switch is used to set the SE3 protective device as a
through-traffic photocell with automatic timed closing.
7 ON The photocell is activated as a through-traffic
photocell, after the photocell has been passed,
the hold-open phase is reduced.
7 OFF
The photocell is not activated as a through-
traffic photocell. If, however, automatic timed
closing is activated and the photocell
interrupted after the hold-open phase has
elapsed, the hold-open phase will be reset to
the preset time.
DIL switch 115.8.8
Setting up the reversal limits
See Chapter f Reversal limit, page 28
DIL switch 125.8.9
Starting point for slow speed when opening and closing:
See Chapter f Changing the starting point for slow speed
when opening and closing, page 28
TR10A059-C RE / 10.2008 29
ENGLISH
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann Schuifhekaandrijving at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann Schuifhekaandrijving in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 7,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info