655857

Hormann HST - Side sectional door Manual

9
Zoom out
Zoom in
Previous page
1/136
Next page
Before fitting the door, the door opening and the building
floor must be completely finished. The door opening must
be horizontal and perpendicular, the building floor in the
area in which the door travels must be flat and horizontal
(see Figure1).
Observe the following during fitting:
• Establish a secure connection with the building
structure.
• Check that the fixing materials supplied are suitable for
the given structural conditions.
• Always obtain the permission of the structural engineer
before fastening the door to supporting structural
elements.
• Ensure adequate water run-off in the area of the floor
rail and the frame parts, otherwise there is a danger of
corrosion.
• Ensure sufficient drying and ventilation in the building,
otherwise there is danger of corrosion.
• The door must be effectively protected before carrying
out plastering and paintwork, as splashes of mortar,
cement, plaster, paint etc. can damage the door
surface.
• Protect the door from caustic, aggressive substances,
e.g. nitrous reactions from stones or mortar, acids,
alkali solutions, de-icing salt, aggressive paints or
sealants. Failure to do so could lead to corrosion.
▶
To ensure simple and secure fitting, please follow
the work steps listed in the illustrated section.
4 Operation
4.1 Door operation
WARNING
Danger of injury due to door travel
The side sectional door closes horizontally; persons or
objects may be trapped.
▶
When in operation, make sure that neither persons,
children in particular, nor objects are located within
the door's area of travel.
▶
Always keep the opening area of the door clear.
▶
Do not operate the door in strong winds.
The door must only be operated by suitably instructed
persons. If the side sectional door is competently fitted
and inspected, it can be easily moved and operated.
4.1.1 Manually operated doors
Note the separate fitting instructions for manually operated
doors (see Figures2.6a / 2.6b and 4a.2 / 4b.2).
WARNING
Danger of injury due to improper operation
Persons or objects may be trapped if the door is
operated improperly.
▶
Only open and close the door using the supplied
operating elements; these ensure a controlled,
smooth action.
▶
When closing the door, make sure that the latches
engage fully and correctly.
4.1.2 Power-driven doors
The automation of a door requires that special safety
regulations be observed.
Consult your supplier.
CAUTION
Danger of crushing between the door and wall
Crushing may occur if the space between the automated
door in the open end-of-travel position and the rear
garage wall is ≤500mm.
▶
In this case, fit a buffer sealing to the last section as
well (see Figure4a.6 / 4b.5).
5 Cleaning and Care
ATTENTION
Scratches on the panes due to improper cleaning
Rubbing the panes causes scratches.
▶
Dirt and dust particles must first be thoroughly rinsed
off with water. If necessary, only wash with water, a
pH-neutral household detergent and a soft, clean
cloth.
Clear water is sufficient for cleaning and care. Use
warm water together with a neutral, non-abrasive cleaning
agent (household detergent, pH value 7) if more heavily
soiled. To preserve the surface characteristics, regular
cleaning must be carried out at least every 3 months
(outside of door, seals). The slide area behind the side
seals must be kept permanently clean so that it offers a
smooth sliding surface.
A variety of environmental influences (e.g. maritime
climate, acids, road salt, air pollutants, paint damage) may
make additional protective coating necessary (seePaint
treatment on page10).
6 Inspection and Maintenance
6.1 Inspections and maintenance
WARNING
Danger of injury due to defective safety components
Important safety components may fail or become
defective if not sufficiently inspected and maintained.
▶
Have a qualified person perform inspection and
maintenance work at regular intervals.
The following inspection and maintenance tasks must be
carried out by a specialist in accordance with these
instructions, before initial operation and at least once a
year.
6.1.1 Fixing points
▶
Check all the fixing points on the door and the building
structure and make sure that all the fastenings are
securely seated and, if necessary, retighten.
4011312 RE / 06.2015
9
ENGLISH
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann HST - Side sectional door at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann HST - Side sectional door in the language / languages: All languages as an attachment in your email.

The manual is 19,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hormann HST - Side sectional door

Hormann HST - Side sectional door Usermanual and installation guide - All languages - 136 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info