655860
8
Zoom out
Zoom in
Previous page
1/124
Next page
2.3 Environmental conditions
ATTENTION
Damage due to temperature differences
Differences in the inside and outside temperatures may
cause deflection of the door elements (bi-metal effect).
This may result in damage when the door is operated.
Comply with the operating conditions.
The door is intended for the following operating conditions:
Temperature:
• Exterior side – 40 °C to + 60 °C
• Interior side – 20 °C to + 60 °C
Relative humidity: 20 % to 90 %
3 Fitting
WARNING
Danger of injury as the result of structural modifications
Changing or removing functional parts may put important
safety components out of action. Uncontrolled door
travel could occur and persons or objects may be
trapped as a result.
Do not alter or remove any functional parts.
Do not attach any additional components. The
torsion springs are precisely matched to the door leaf
weight. Additional components may overload the
springs.
If equipping the door with an operator, pay attention
to the instructions provided by the manufacturers of
the door and operator. Only use the original
connections of the door manufacturer!
Before fitting the door, the door opening and the building
floor must be completely finished.
Observe the following during fitting:
• Establish a secure connection with the building
structure.
• Check that the fixing materials supplied are suitable for
the given structural conditions.
• Do not fasten the door system to supporting structural
members unless you have obtained the prior approval
of the structural engineer.
• Ensure adequate water run-off in the area of the
bottom seal and the frame parts, otherwise there is
danger of corrosion (see Technical Manual).
• Ensure sufficient drying and ventilation in the building,
otherwise there is danger of corrosion.
• The door must be effectively protected before carrying
out plastering and paintwork, as splashes of mortar,
cement, plaster, paint etc. can damage the door
surface.
• Protect the door from caustic, aggressive substances,
e.g. nitrous reactions from stones or mortar, acids,
alkali solutions, de-icing salt, aggressive paints or
sealants. Failure to do so could lead to corrosion.
To ensure simple and secure fitting, please follow
the work steps listed in the illustrated section.
3.1 Tensioning the springs
WARNING
Danger of injury due to high torques
Springs are under high torque stress and may discharge
high forces if they are not secured during tensioning.
Fix the door leaf to prevent movement before
tensioning the springs.
The number of tensioning revolutions specified on the type
plate is an approximate value only.
When the springs are tensioned correctly, the moving door
leaf has a slight tendency to pull upwards.
Each time the door is serviced, the tension of the
springs should be checked and, if necessary,
subsequently re-adjusted.
Before putting the door into operation for the first
time, inspect the door according to the chapter
Inspection and Maintenance!
4 Operation
4.1 Operating the door
WARNING
Danger of injury during door travel
The sectional door closes to the bottom vertically;
persons or objects may be trapped.
When in operation, make sure that neither persons,
children in particular, nor objects are located within
the door's area of travel.
Always keep the opening area of the door clear.
Do not operate the door in strong winds.
The door must only be operated by suitably instructed
persons. If the sectional door is competently fitted and
inspected, it can be easily moved and operated.
4.1.1 Manually operated doors
WARNING
Danger of injury due to improper operation
Persons or objects may be trapped if the door is
operated improperly.
Only open and close the door using the supplied
operating elements; these ensure a controlled,
smooth action.
When closing the door, make sure that the latches
engage fully and correctly.
4.1.2 Power-driven doors
The automation of a sectional door requires that special
safety regulations be observed. Consult your supplier.
4.2 Locking and unlocking
The door is not locked when closed with the grip handle.
This is done by using the key or locking lever on the lock.
8
3 048 942 RE / 10.2016
ENGLISH
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hormann BR40N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hormann BR40N in the language / languages: All languages as an attachment in your email.

The manual is 8,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info