640986
9
Zoom out
Zoom in
Previous page
1/39
Next page
1716
DO NOT stand on running belt while calibrating – stand on
the side rails. The treadmill will fluctuate between low and
high speeds for several minutes until calibration is complete.
WARNING
TROUBLESHOOTING HEART RATE
(GRIP-PULSE ONLY)
Check your exercise environment for sources of
interference such as fluorescent lights, computers,
underground fencing, home security systems or
appliances containing large motors. These items may
cause erratic heart rate readouts.
You may experience an erratic readout under the
following conditions:
Gripping the heart rate handlebars too tight. Try to
maintain moderate pressure while holding onto the
heart rate handlebars.
Constant movement and vibration due to constantly
holding the heart rate handlebars while exercising.
If you are receiving erratic heart rate readouts, try
to only hold the grips long enough to monitor your
heart rate.
When you are breathing heavily during a workout.
When your hands are constricted by wearing a ring.
When your hands are dry or cold. Try to moisten
your palms by rubbing them together to warm.
Anyone with heavy arrhythmia.
Anyone with arteriosclerosis or peripheral
circulation disorder.
Anyone whose skin on the measuring palm is
especially thick.
PROBLEM: Operating speed appears inaccurate.
SOLUTION: Auto-calibrate the treadmill:
Power on the treadmill and have the safety key in position on
the console. Press and hold the elevation “+” and speed “–”
buttons for approximately 5 seconds to enter the Engineering
Mode. The console will beep and “ENG0” appears in the
display.
Press the Speed “+” or “–” button until “ENG2” appears in the
display.
Press, “ENTER” to select. Press, “START” to begin. The treadmill
running belt will begin to move automatically and the auto-
calibration sequence will properly set and store the speed
values.
Upon successful calibration, the treadmill will beep several
times. The console will automatically exit Engineering Mode
and return to the start-up screen.
NOTE: Some treadmill models do not have auto-calibrate. Turn the
treadmill off and disconnect the power cord. Check the console
cable for pinches and make sure it is connected properly to both
the upper and lower boards.
TROUBLESHOOTING
If this troubleshooting section does not remedy the problem,
discontinue use and turn the power off.
PLEASE CALL YOUR LOCAL DEALER.
The following information may be asked of you when you
call. Please have these items readily available:
Model Name
Serial Number
Date of Purchase (receipt or credit card statement)
In order for your local dealer to service your treadmill they
may need to ask detailed questions about the symptoms that
are occurring. Some troubleshooting questions that may be
asked are:
How long has this problem been occurring?
Does this problem occur with every use? With every
user?
If you are hearing a noise, does it come from the front
or the back? What kind of noise is it (thumping, grinding,
squeaking, chirping etc.)?
Has the machine been lubricated and maintained per the
maintenance schedule?
Answering these and other questions will give the technicians
the ability to send proper replacement parts and the service
necessary to get you and your treadmill running again!
MAINTENANCE
Preventative maintenance is the key to smooth operating
equipment, as well as keeping the users liability to a
minimum. Equipment needs to be inspected at regular
intervals. Defective components must be replaced
immediately. Improperly working equipment must be kept
out of use until it is repaired. Ensure that any person(s)
making adjustments or performing maintenance or repair of
any kind is qualified to do so.
AFTER EACH USE (DAILY)
Clean and inspect, following these steps:
Turn off the treadmill with the ON/OFF switch, then
unplug the power cord at the wall outlet.
Wipe down the running belt, deck, motor cover, and
console casing with a damp cloth. Never use solvents, as
they can cause damage to the treadmill.
Inspect the power cord. If the power cord is damaged,
contact your local dealer.
Make sure the power cord is not underneath the
treadmill or in any other area where it can become
pinched or cut.
Check the tension and alignment of the running belt.
Make sure that the treadmill belt will not damage any
other components on the treadmill by being misaligned.
EVERY WEEK
Clean underneath the treadmill, following these steps:
Turn off the treadmill with the ON/OFF switch, then
unplug the power cord at the wall outlet.
JHT14_GUIDE_TM_ID_Rev1_0.indd 16-17 7/13/15 3:40 PM
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Horizon Fitness ADVENTURE 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Horizon Fitness ADVENTURE 1 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Horizon Fitness ADVENTURE 1

Horizon Fitness ADVENTURE 1 Installation Guide - English, German, Dutch, French - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info