2
GB
USING YOUR CLEANER
USING YOUR CLEANER
CLEANER MAINTENANCE
Extract power cord and plug it into the power supply. Do not pull the cord beyond the 1.
red marker. [5]
To adjust the length of the 2. telezoom tube hold the nozzle in place with your foot, pull the
telezoom trigger and raise or lower the handle to the most comfortable cleaning position.
[6]
Select the type of surface to be cleaned by pressing the pedal in the nozzle. 3. [7]
Hard Floor – Brushes are lowered to protect the oor.
Carpet – Brushes are raised for the deepest clean.
Switch the cleaner on by pressing the On/O Button on the cleaner main body. 4. [8]
Adjust the suction by sliding the suction regulator to the desired level. 5. [9]
Switch o at the end of use by pressing the On/O Button. Unplug and press the cord 6.
rewind button to wind the power cord back into the cleaner. [10]
To store your cleaner adjust telescopic tube to
the lowest height setting and park the 7.
nozzle in the park position on the cleaner main body. [11]
Please see the model specication on the packaging label for inclusion of accessories to
individual models. All accessories can be purchased separately from Hoover. (See Hoover
Spares and Consumable section).
All accessories can be tted to the end of the navigator handle or the end of the telescopic tube.
3 in 1 Accessory – Combines several functions in one, with maximum exibility by the rotating
body. Reach into awkward areas by rotating the body. The 3 in 1 tool can be stored neatly
underneath the h
ose handle. [1]
Crevice Tool – For corners and hard to reach areas. [12]
Furniture Nozzle – For soft furniture and fabrics. [13]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. To extend the
brushes push the button on the body of the tool. [14]
Parquet Caresse Nozzle* – For parquet oors and other delicate oors. [1Y]
Grand Turbo Nozzle* – Use the turbo nozzle for deep cleaning on carpets. [1X]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deepcleaning
on textile surfaces a
nd other hard to clean areas. Particularly suitable for pet hairs removal.
[1V]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deepcleaning
on textile surfaces and other hard to clean areas, particularly suitable for allergen removal.
[1W]
IMPORTANT: Do not use the turbo and mini turbo nozzles on rugs with long fringes, animal
hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush
is rotating.
Emptying the Dust Container
When the dust reaches
the max level indicator in the container empty the dust container.
IMPORTANT: To maintain optimum performance do not allow the dust to sit higher than the
max level.
Release the container carry handle by lifting the centre latch to detach the dust container 1.
from the main cleaner and pull upward to remove. [15]
Hold the dust container over a bin with one hand and with the other pull the dust 2.
container catch to open the door and empty. [16]
Close the dust container door and ret to the cleaner main body. To lock in place push the 3.
container carry handle down until the latch connects with the main body of the cleaner.
Once correctly retained the carry handle will sits ush with the top of the cleaner.
Cleaning the washable lters
The cleaner is
tted with two blue hepa lter packs. To maintain optimum cleaning performance
regularly remove the the lters and tap against the side of the bin to release dust. The lters
should be washed every 3 months or when the lter has excessive dust level.
IMPORTANT: Regularly check and maintain the lters.
IMPORTANT: Always ensure the lter pack is fully dry before use.
To access the Pre-Motor lter:
Unlock the lter door by pulling the lter latch upwards. Open the lter door. 1. [17]
Remove the lter pack by pressing down on the retainer catch to release. The lter pack 2.
will pop up. Slide the lter pack out. [18]
Unlatch the lter pack frame.3.
Remove the micro lter from the pack
.4.
Gently tap and wash the micro lter attached to the lter frame using warm water. Do not 5.
use hot water or detergents. Remove excess water from the lter and leave to dry fully
before re-using. [21]
Reassemble to lter pack once fully dry and ret to the cleaner. Press on the top of the 6.
lter to ensure it clips back into place.
