667154
6
Zoom out
Zoom in
Previous page
1/28
Next page
EN
!
2
Thank-you for choosing a Hoover washing
machine. We are proud to always offer
new, innovative and technologically
advanced products, with a complete range
of home appliances to ensure true
assistance in your daily routine.
We suggest you register your product at
www.registerhoover.com to gain faster
access to supplementary services solely
reserved to our most loyal customers.
Carefully read this manual for correct and
safe appliance use and for helpful tips on
efficient maintenance.
Only use the washing machine
after carefully reading these instructions.
We recommend you always keep this
manual on hand and in good conditions for
any future owners.
Please check that the appliance is
delivered with this instruction manual,
warranty certificate, service centre address
and energy efficiency label. Also check that
plugs, curve for drain hose and liquid
detergent or bleach tray (only on some
models) are included. We recommend you
keep all these components.
Each product is identified by a unique 16-
character code, also called the “serial
number”, printed on the sticker affixed to
the appliance (porthole area) or in the
document envelope found inside the
product. This code is a sort of specific
product ID card that you will need to
register it and should you need to contact
the Hoover Customer Service Centre.
This appliance is marked according to
the European directive 2012/19/EU
on Waste Electrical and Electronic
Equipment (WEEE).
Environmental conditions
Contents
!
EN
3
1. GENERAL SAFETY
RULES
! This appliances is intended to
be used in household and
similar applications such as:
- Staff kitchen areas in shops, offices
and other working environments;
- Farm houses;
- By clients in hotels, motels and
other residential type environments;
- Bed and breakfast type environments.
A different use of this appliance
from household environment
or from typical housekeeping
functions, as commercial use by
expert or trained users, is excluded
even in the above applications. If
the appliance is used in a manner
inconsistent with this it may reduce
the life of the appliance and may
void the manufacturer’s warranty.
Any damage to the appliance or
other damage or loss arising
through use that is not consistent
with domestic or household use
(even if located in a domestic or
household environment) shall not
be accepted by the manufacturer to
the fullest extent permitted by law.
! This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental
capabilities or lack of experience
and knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
! Children should be supervised
to ensure that they do not play
with the appliance.
! Children of less than 3 years
should be kept away unless
continuously supervised.
! If the supply cord is damaged, it
must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
! Only use the hose-sets
supplied with the appliance for
the water supply connection
(do not reuse old hose-sets).
! Water pressure must be between
0,05 MPa and 0,8 MPa.
! Make sure that a carpet do not
obstruct the base of the machine
and ventilation openings.
! The OFF condition is reached
by
placing the reference mark on
the programmes control/knob in
the vertical position. Any other
different position of such control
sets the machine in ON condition
(only for models with programmes
knob).
!
4
! The final part of a washer dryer
cycle occurs without heat (cool
down cycle) to ensure that the
items are left at a temperature
that ensures that the items will
not be damaged.
! After installation, the appliance
must be positioned so that the
plug is accessible.
! The appliance must not be
installed behind a lockable
door, a sliding door or a door
with a hinge on the opposite
side to that of the washer
dryer, in such way that a full
opening of the washer dryer
door is restricted.
! The maximum load capacity of
dry clothes depends on the
model used (see control panel).
! The appliance is not to be used
if industrial chemicals have
been used for cleaning.
! Do not dry unwashed items in
the washer dryer.
! Items that have been soiled with
substances such as cooking oil,
acetone, alcohol, petrol, kerosene,
spot removers, turpentine, waxes
and wax removers should be
washed in hot water with an extra
amount of detergent before being
dried in the washer dryer.
! Items such as foam rubber
(latex foam), shower caps,
waterproof textiles, rubber
backed articles and clothes or
pillows fitted with foam rubber
pads should not be dried in the
washer dryer.
! Fabric softeners, or similar
products, should be used as
specified by the fabric softener
instructions.
! Oil-affected items can ignite
spontaneously, especially when
exposed to heat sources such
as a washer dryer. The items
become warm, causing an
oxidation reaction in the oil,
Oxidation creates heat. If the
heat cannot escape, items can
become hot enough to catch
fire. Piling, stacking or storing
oil-effected items can prevent
heat from escaping and so
create a fire hazard.
! If it is unavoidable that fabrics
contain vegetable or cooking
oil or have been contaminated
WARNING:
never stop a washer dryer before
the end of the drying cycle
unless all items are quickly
removed and spread out so that
the heat is dissipated.
!
EN
5
by hair care products be
placed in a washer dryer they
should first be washed in hot
water with extra detergent -
this will reduce, but not
eliminate, the hazard.
! Remove all objects from
pockets such as lighters and
matches.
! To consult the product fiche
please refer to the manufacturer
website.
! Before cleaning or maintaining
the washing machine, unplug
the appliance and turn off the
water faucet.
! Make sure the electrical
system is grounded. Otherwise,
seek qualified professional
assistance.
! Please do not use converters,
multiple sockets or extension
cords.
! Make sure there is no water in
the drum before opening the
porthole.
! Do not pull on the power cord
or appliance to unplug the
machine.
! Do not expose the washing
machine to rain, direct sunlight
or other weather elements.
! When moving, do not lift the
washing machine by the knobs
or detergent drawer; during
transport, never rest the
porthole on the trolley. We
recommend two people lift the
washing machine.
! In the event of fault and/or
malfunction, turn off the
washing machine, close the
water faucet and do not tamper
with the appliance.
Immediately contact the
Customer Service Centre and
only use original spare parts.
Failure to observe these
instruction may jeopardise
appliance safety.
Appliance complies with
European Directives:
! 2006/95/EC (LVD);
! 2004/108/EC (EMC);
! 2009/125/EC (ErP);
! 2011/65/EU (RoHS)
and subsequent amendments.
Safety instructions
WARNING:
water may reach very high
temperatures during the
wash cycle.
!
6
2. INSTALLATION
WARNING:
keep packaging materials
away from children.
!
EN
7
! Connect the water tube to the faucet, only
using the drain tube supplied with the
washing machine (fig. 3).
DO NOT OPEN THE FAUCET.
! Some models may include one or more of
the following features:
! HOT&COLD (fig. 4):
water mains connection settings with hot
and cold water for higher energy savings.
Connect the grey tube to the cold water
faucet and the red one to the hot water
faucet. The machine can be connected to
the cold water faucet only: in this case,
some programs may start a few minutes
later.
! AQUASTOP (fig. 5):
a device located on the supply tube that
stops water flow if the tube deteriorates;
in this case, a red mark will appear in the
window A and the tube must be
replaced. To unscrew the nut, press the
one-way lock device "B".
! AQUAPROTECT SUPPLY TUBE WITH
GUARD (fig. 6):
Should water leak from the primary
internal tube "A", the transparent
containment sheath "B" will contain water
to permit the washing cycle to complete.
At the end of the cycle, contact the
Customer Service Centre to replace the
supply tube.
! Near the washing machine to the wall,
being careful that the tube is not bent or
crushed, and place the drain tube in the
tub or, preferably, connect it to a wall
drain at least 50 cm high with diameter
greater than the washing machine tube
(fig. 7).
3
1
4
B
A
5
B
A
6
min 50 cm
max 85 cm
+2,6 mt
max
max 100 cm
min 4 cm
Hydraulic connections
Setting
!
8
! Level the appliance using the feet as
illustrated in figure 8:
a. turn the nut clockwise to release the
screw;
b. rotate the foot to raise or lower it until it
adheres to the floor;
c. lock the foot, screwing in the nut, until it
adheres to the bottom of the washing
machine.
! Plug in the appliance.
The detergent draw is split into 3
compartments as illustrated in figure 9:
! compartment "1": for prewash detergent;
! compartment : for special additives,
softeners, starch fragrances, etc.;
! compartment "2": for washing detergent.
A liquid detergent cup is also included in
some models (fig. 10). To use it, place it in
compartment "2". This way, liquid
detergent will only enter the drum at the
right time. The cup can also be used for
bleach when the “Rinse” program is
selected.
WARNING:
contact the Customer Service Centre
should the power cord need
replacement.
Detergent drawer
WARNING:
only use liquid products; the washing
machine is set to automatically dose
additives at each cycle during the last
rinse.
WARNING:
some detergents are hard to remove.
In this case we recommend using the
specific container to be placed in the
drum (example in figure 11).
!
EN
9
3. PRACTICAL TIPS
WARNING: when sorting laundry, make
sure:
- have eliminated metallic objects such as
barrettes, pins, coins, from laundry;
- to have buttoned pillow cases, closed
zips, tied loose belts and long robe
ribbons;
- to have removed rollers from curtains;
- to have carefully read clothing washing
labels;
- to have removed any persistent stains
using specific detergents.
! When washing rugs, bedcovers or other
heavy clothing, we recommend you avoid
centrifuging.
! To wash wool, make sure the item can be
machine washed and marked by the
“Pure virgin wool” symbol with the “Does
not mat” or “Machine washable” label.
A guide environmentally friendly and
economic use of your appliance.
Maximise The Load Size
! Achieve the best use of energy, water,
detergent and time by using the
recommended maximum load size.
Save up to 50% energy by washing a full
load instead of 2 half loads.
Do you need to pre-wash?
! For heavily soiled laundry only!
SAVE detergent, time, water and
between 5 to 15% energy consumption
by NOT selecting Prewash for slight to
normally soiled laundry.
Is a hot wash required?
! Pretreat stains with stain remover or soak
dried in stains in water before washing to
reduce the necessity of a hot wash
programme.
Save up to 50% energy by using a 60°C
wash programme.
Before using a drying programme
! SAVE energy and time by selecting a
high spin speed to reduce the water
content in laundry before using a drying
programme.
Following is a quick guide with tips and
recommendations on detergent use at the
various temperatures. In any case, always
read the instructions on the detergent for
correct use and doses.
Load tips
Helpful suggestions for the user
When washing heavily soiled whites,
we recommend using cotton
programs of 60°C or above and a
normal washing powder (heavy duty)
that contains bleaching agents that at
medium/high temperatures provide
excellent results.
For washes between 40°C and 60°C
the type of detergent used needs to be
appropriate for the type of fabric and
level of soiling.
Normal powders are suitable for “white”
or colour fast fabrics with high soiling,
while liquid detergents or “colour
protecting” powders are suitable for
coloured fabrics with light levels of
soiling.
For washing at temperatures below
40°C we recommend the use of liquid
detergents or detergents specifically
labeled as suitable for low temperature
washing.
For washing wool or silk, only use
detergents specifically formulated for
these fabrics.
!
10
4. MAINTENANCE AND
CLEANING
To clean the washing machine exterior, use
a damp cloth, avoiding abrasives, alcohol
and/or solvents. The washing machine does
not require any special care for ordinary
cleaning: clean drawer compartments and
the filter; some tips on how to move the
machine or on long periods of disuse are
provided below.
! We recommend you clean the drawer to
avoid accumulating detergent and
additive residue.
! To do this, extract the drawer using slight
force, clean it with running water and
reinsert it in its housing.
! The washing machine comes with a
special filter able to trap large residue,
such as buttons or coins, which could
clog the drain.
! Only available on certain models: pull out
the corrugated hose, remove the stopper
and drain the water into a container.
! Before unscrewing the filter, we
recommend you place an absorbent cloth
under it to keep the floor dry.
! Turn the filter counter-clockwise to the
limit stop in the vertical position.
! Remove and clean the filter; when
finished, replace it turning it clockwise.
! Repeat the previous steps in reverse
order to reassemble all parts.
! Should the washing machine be stored in
an unheated room for a long period of
time, drain all water from tubes.
! Unplug the washing machine.
! Detach the tube from the strap and lower
it, fully draining water into a bowl.
! Secure the drain tube with the strap when
finished.
Drawer cleaning
Filter cleaning
Suggestions for moves or
prolonged disuse
!
EN
11
5. QUICK USER GUIDE
This washing machine automatically adapts
the level of the water to the type and
quantity of washing. This system gives a
decrease in energy consumption and a
sensible reduction in washing times.
! Turn on the washing machine and select
the required program.
! Adjust the washing temperature if
necessary and press the required "option"
buttons.
! Press the START/PAUSE button to start
washing.
! The message "end" will appear on the
display or the corresponding led will turn
on at the end of the program.
! Turn off the washing machine.
For any type of wash, see the program
table and follow the operating sequence
as indicated.
Water pressure: min 0,05 Mpa / max 0,8 Mpa
Spin r.p.m.: See rating plate.
Power input / Power current fuse amp /
Supply voltage: See rating plate.
6. CONTROLS AND
PROGRAMS
A
Programme selector with OFF
position
B
START/PAUSE button
C
DELAY START button
D
PREWASH button
E
DRYING SELECTION button
F
SPIN SPEED button
G
TEMPERATURE SELECTION
button
H
RAPID LENGTH button
I
Digital display
L
BUTTONS indicator lights
M
DOOR LOCKED indicator light
N
SPIN SPEED indicator lights
O
TEMPERATURE SELECTION
indicator lights
P
RAPID LENGTH indicator lights
Program selection
DRYING
If you would like the drying cycle to
begin automatically after washing,
select the programme required using
the DRYING SELECTION button.
Or you can finish the wash and then
select the drying programme and
load size.
Wait until the porthole locked light
turns off: about 2 minutes after the
program ends.
Technical data
!
12
! Press the START/PAUSE button to start
the selected cycle.
! Once a programme is selected the
programme selector remains stationary on
the selected programme till cycle ends.
! Switch off the washing machine by
turning the selector to OFF.
! Press to start the selected cycle.
ADD OR REMOVE ITEMS AFTER THE
PROGRAMMES HAS STARTED (PAUSE)
! Press and hold the START/PAUSE
button for about 2 seconds (some
indicator light and the time remaining
indicator will flash, showing that the
machine has been paused).
! Wait 2 minutes until the safety device
unlocks the door.
! After you have added or removed items,
close the door and press the
START/PAUSE button (the programme
will start from where it left off).
CANCELLING THE PROGRAMME
! To cancel the programme, set the
selector to the OFF position.
! This button allows you to pre-programme
the wash cycle to delay the start of the
cycle for up to 24 hours.
! To delay the start use the following
procedure:
- Set the required programme.
- Press the button once to activate it (h00
appears on the display) and then press
it again to set a 1 hour delay (h01
appears on the display). The pre-set
delay increases by 1 hour each time the
button is pressed, until h24 appears on
the display, at which point pressing the
button again will reset the delay start to
zero.
- Confirm by pressing the START/PAUSE
button (the light on the display starts to
flash). The countdown will begin and
when it has finished the programme will
start automatically.
Opening the door
A special safety device prevents the
door from being opened immediately
after the end of the cycle.
Wait for 2 minutes after the wash
cycle has finished and the "Door
Security" light has gone out before
opening the door.
PROGRAMME selector with OFF
position
When the programme selector is turned
the display lights up to show the settings
for the programme selected.
For energy saving, at the end of the
cycle or with an inactivity period, the
display level contrast will decrease.
N.B.: To switch the machine off, turn
the programme selector to the OFF
position.
The programme selector must be
returned to the OFF position at the end
of each cycle or when starting a
subsequent wash cycle prior to the next
programme being selected and started.
START/PAUSE button
Close the door BEFORE selecting the
button START/PAUSE.
When the START/PAUSE button has
been pressed, the appliance can take
few seconds before it starts working.
DELAY START button
!
EN
13
! It is possible to cancel the delay start by
turning the programme selector to OFF.
If there is any break in the power supply
while the machine is operating, a special
memory stores the selected programme
and, when the power is restored, it
continues where it left OFF.
It allows you to do a preliminary wash at the
beginning of the cycle. The temperature does
not exceed 40°C and in any case it does not
exceed the maximum temperatures of the
selected washing program (ex. the temperature
of HAND program will be 30°C.
! Ensure that the programme selector is
not in the OFF position then press the
button to select the required drying
programme: an indicator will light to
display the drying result selected each
time you press the button.
! To cancel the selection before the start of
a drying programme, press the button
repeatedly until the indicators go out or
return the programme selector to the OFF
position.
! To cancel the cycle during the drying
phase, hold the button down for about
3 seconds until the cooling indicator
lights up.
! Given the high temperature inside the
drum, we recommend that you allow the
dryer to complete the cool down period
before returning the programme selector
to the OFF position and removing the
laundry.
! By pressing this button, it is possible to
reduce the maximum speed, and if you
wish, the spin cycle can be cancelled.
! To reactivate the spin cycle press the button
until you reach the spin speed you would
like to set.
! It is possible to modify the spin speed
without pausing the machine.
When you select a program, the light
illuminates the recommended temperature.
It is also possible to change the
temperature but not over the maximum in
order to save the fabrics.
The button becomes active when you select
the RAPID program on the knob; it allows you
to select one of three durations indicated.
The option buttons should be selected
before pressing the START/PAUSE
button.
If an option is selected that is
not compatible with the selected
programme then the option indicator
first flashes and then goes off.
PREWASH button
DRYING SELECTION button
SPIN SPEED button
To prevent damage to the fabrics, it is
not possible to increase the speed
over that which is automatically
suitable during the selection of the
program.
The machine is fitted with a special
electronic device, which prevents the
spin cycle should the load be
unbalanced.
This reduces the noise and vibration in
the machine and so prolongs the life of
your machine.
TEMPERATURE SELECTION
button
RAPID LENGTH button
!
14
The display’s indicator system allows you to
be constantly informed about the status of
the machine.
1) DOOR LOCKED INDICATOR LIGHT
! The indicator light is illuminated when the
door is fully closed.
! When START/PAUSE is pressed on
the machine with the door closed, the
indicator will flash momentarily and then
illuminate.
! A special safety device prevents the door
from being opened immediately after the
end of the cycle. Wait for 2 minutes after
the wash cycle has finished and the
DOOR LOCKED light has gone out before
opening the door. At the end of the cycle
turn the programme selector to OFF.
2) CYCLE DURATION
! When a programme is selected the
display automatically shows the cycle
duration, which can vary, depending on
the options selected.
! Once the programme has started you will
be kept informed constantly of the time
remaining to the end of the wash.
! The appliance calculates the time to the
end of the selected programme based
upon a standard loading, during the cycle,
the appliance corrects the time to that
applicable to the size and composition of
the load.
! If automatic washing/drying is selected, at
the end of the wash phase, the drying time
remaining to the end will be shown on the
display.
3) BUTTONS INDICATOR LIGHTS
! These light up when the relevant buttons
are pressed.
! If an option is selected that is not
compatible with the selected programme
then the light on the button first flashes
and then goes off.
4) SPIN SPEED indicator lights
The indicator lights show the spin speed of
the selected programme that can be
changed or omitted by the relevant button.
5) TEMPERATURE SELECTION indicator
lights
The indicator lights show the washing
temperature of the selected programme
that can be changed (where allowed) by the
relevant button.
6) RAPID LENGTH indicator lights
The indicator lights show the rapid
programmes that can be selected by the
relevant button.
Digital Display
Close the door BEFORE selecting the
START/PAUSE button.
If the door is not properly closed,
the light will continue to flash for
about 7 seconds, after which the
start command will be automatically
delete. In this case, close the door
in the proper way and press the
START/PAUSE button.
!
EN
15
7) DRYING PROGRAMME INDICATORS
The indicators display the type of the drying
programme.
Automatic drying programmes
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
Iron dry programme (that leaves the
laundry ready for ironing).
Cupboard dry programme (for
items that will be put away without
ironing).
! By selecting one of these automatic
programmes, the washer dryer will
calculate the time needed for drying and
the level of moisture remaining in the
laundry, according to the load and drying
type selected.
! After pressing the START/PAUSE button,
the display will show the drying time
remaining.
Cool down phase
Activated during the final cool down
period, in the last 10/20 minutes of
each drying phase.
Useful tips
! Your washer dryer automatically ends the
cycle when it reaches the selected drying
level.
! In order to ensure the correct operation of
the appliance, it is advisable not to
interrupt the drying phase unless it is
absolutely necessary.
The appliance calculates the time to
the end of the selected programme
based upon a standard loading.
During the cycle, the appliance
corrects the time according to the size
and composition of the load.
!
16
2
1
PROGRAM
kg *
(MAX.)
TEMP.°C
DETERGENT
Recommended
Max.
2
1
ActivEco 20°C
2)
6
7
8
9
10
20°
20°
Baby 60°C
2)
4
4,5
5,5
6
6,5
60°
60°
Daily 59 Min.
2)
2
2,5
3
3
3,5
40°
60°
Rapid (14/30/44 Min.)
1)
2)
1
1
1,5
1,5
1,5
30°
30°
2
2,5
2,5
2,5
2,5
30°
30°
3
3,5
3,5
3,5
3,5
30°
40°
Cottons**
2)
6
7
8
9
10
40°
90°
( )
Delicates
2
2,5
2,5
2,5
2,5
40°
40°
Auto Clean
Rinse 2)
-
-
-
-
-
-
-
Drain & Spin
2)
-
-
-
-
-
-
-
Mixed
2)
3
3,5
4
4,5
5
40°
60°
( )
Hand & Silk
1
1
2
2
2
30°
30°
Wool
1
1
2
2
2
40°
40°
Low Heat
(drying)
3
3,5
4
4,5
5
-
-
High Heat
(drying)
5
5
5
6
6
-
-
Rapid W&D 59 Min.
1,5
1,5
1,5
1,5
1,5
30°
30°
Table of programmes
!
EN
17
( )
Only with PREWASH option
selected (programmes with
PREWASH option available).
(Only for models with liquid
detergent compartment)
When only a limited number of
articles have stains which require
treatment with liquid bleaching
agents, preliminary removal of
stain can be carried out in the
washing machine.
Pour the bleach into the liquid
bleach container, inserted into the
compartment marked "2" in the
detergent drawer, and set the
special programme RINSE.
When this phase has terminated,
turn the programme selector on
the OFF position, add the rest of
the fabrics and proceed with a
normal wash on the most suitable
programme.
1)
Selecting the RAPID program on
the knob, it will be possible to
select with the RAPID LENGTH
button, one of the three rapid
programs available among 14 Min.,
30 Min. and 44 Min..
2)
Programmes for automatic drying.
INFORMATION FOR THE TEST
LABORATORIES (Ref. EN 50229
Standards)
Washing
Use the programme ** with the maximum
degree of soiling selected, maximum spin
speed and a temperature of 60°C.
Programme recommended also for test
with a lower temperature.
Drying
First drying with A kg (a load consist:
pillowcases and hand-towels) selecting
the cotton drying programme
(
) cupboard dry (
).
Second drying with B kg (a load consist:
sheets and hand towels) selecting the
cotton drying programme (
)
cupboard dry (
).
Capacity
(washing)
(kg)
A (kg)
B (kg)
First
drying
Second
drying
6
5
1
7
5
2
8
5
3
9
6
3
10
6
4
!
18
To clean different types of fabrics and
various levels of dirt, the washing machine
has specific programs to meet every need
of washing (see table of programmes).
ActivEco 20°C
This innovative programme, allows you to wash
different fabrics and colours together, such as
cottons, synthetics and mixed fabrics at only
20°C and provides an excellent cleaning
performance. Consumption on this program is
about 40% of a conventional 40°C. cottons wash.
Baby 60°C
This program allows you to wash all baby
clothes getting a perfect clean and
sanitizing effect, setting the temperature at
60°C minimum. To optimize the result of the
sanitizing effect we recommend the use of
powder detergent.
Daily 59 Min.
This specially designed programme
maintains the high quality wash
performance whilst greatly reducing the
wash time. The programme is designed for
a reduced load (see table of programmes).
Rapid (14/30/44 Min.)
Washing cycle suggested for low loads and
slightly dirty. With this program it is
recommended to reduce the quantity of
detergent normally used, in order to avoid
unnecessary waste. Selecting the RAPID
program and acting on the button you can
choose one of three programs available.
Cottons
This program is suitable to clean normally
soiled cotton laundry and it is the most efficient
program in terms of combined energy and
water consumptions for washing cotton laundry.
Delicates
This program alternates among moments of
work during breaks and is particularly suitable
for washing delicate fabrics. The wash cycle
and rinses are carried out with a high level of
water to ensure the best performance.
Auto Clean
This program is suited to clean the drum of your
appliance. It is recommended to use this
program every 50 washing cycles, to ensure a
long service life and avoid bad odors. Make sure
to start the program exclusively without laundry in
the machine, using only powder detergent for
washing machine. When the washing cycle
finishes, open the door of the washing machine
to dry the drum.
Rinse
This program performs 3 rinses with an
intermediate spin (which can be reduced or
excluded by using the appropriate button) . It
is used for rinsing any type of fabric, for
example after a wash carried out by hand.
Drain & Spin
The program completes the drain and a
maximum spin. It is possible to delete or reduce
the spin with the SPIN SPEED button.
Mixed
The washing and rinsing are optimized in
the rhythms of rotation of the drum and to
the water levels. The gentle spin, ensures a
reduced formation of creases in the fabric.
Hand & Silk
This programme allows a delicate washing
cycle for garments specified as "Hand Wash
only" and laundry items made from Silk or
specified as "Wash as Silk" on the fabric label.
Wool
This program performs a wash cycle
dedicated to the wool fabrics that can be
washed in a washing machine, or the
articles to be washed by hand.
DRYING
The drum changes direction during the
drying cycle to prevent the laundry from
tangling and producing even more drying.
Cool air is used during the last 10/20
minutes of the drying cycle to minimize
creasing.
Programmes selection
WARNING:
Dispensers used for concentrated
powders and liquid detergents must be
removed from the drum before
commencing the tumble drying
programmes.
!
EN
19
!
20
7. DRYING CYCLE
! Drying guidance advice is general, but
practical experience of using the product
will help you to achieve the best drying
results.
! We recommend setting a lower drying
time than indicated, when first using the
appliance in order to establish the degree
of dryness required.
! We recommend not drying fabrics that
fray easily, such as rugs or garments with
a deep pile, in order to avoid air duct
clogging.
! We recommend that you sort the laundry
by the following methods:
- By drying care symbols, which are
displayed on the clothing labels
Suitable for tumble drying.
Tumble dry at high temperature.
Tumble dry at low temperature only.
DO NOT tumble dry.
- By size and thickness
Whenever the wash load is bigger than
the drying capacity, separate the clothes
according to thickness (e.g. towels from
thin underwear).
- By fabric type
Cottons/linen: towels, cotton jersey, bed
and table linen.
Synthetics: blouses, shirts, overalls, etc.
made of polyester or polyamide, as well
as for cotton/synthetic mixes.
! Only dry pre-spun laundry.
! The washer dryer can perform the
following types of drying:
- Low temperature drying programme
recommended for mixed fabrics
(synthetics/cotton) synthetic fabrics.
- High temperature drying programme
recommended for cotton, terry toweling,
linen, hemp fabrics, etc....
! Open the door.
! Fill with the laundry, not exceeding the
maximum drying load indicated in the
programme table. For large items (e.g.
sheets) or very absorbent items (e.g.
towels or jeans), it is a good idea to
reduce the load.
! Close the door.
If the fabric does not have a care label,
you should assume that it is not
suitable for drying.
During the drying phase the drum will
accelerate to a higher speed to
distribute the load and to optimize the
drying performance.
The correct way to dry
The appliance door is fitted with a
protective shield to prevent contact
with the glass door which can reach
high temperatures, during the drying
cycle.
It should not be necessary to remove
the shield from the machine during
the normal course of use.
!
EN
21
! Turn the programme dial to the more
suitable drying programme for your laundry.
! Select the degree of dryness that you
require choosing one of 3 automatic
programmes:
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
Iron dry programme (that leaves the
laundry ready for ironing).
Cupboard dry programme (for
items that will be put away without
ironing).
! Make sure that the water inlet valve is
open.
! Make sure water drain is correctly
positioned.
! Press the START/PAUSE button.
! The drying phase will begin with the
programme dial fixed on the selected
programme until the end of drying.
! The drying programme indicator will be
on, until the cool down phase begins and
the corresponding indicator is on.
! When the programme is finished the word
"End" will appear on the display. After
5 minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
! After the programme has finished please
wait for about 2 minutes until the DOOR
LOCKED indicator has gone out before
opening the door.
! Switch off the machine by turning the
programme selector to the OFF position.
! Open the door and remove the laundry.
! Turn off the tap.
CANCELLING THE DRYING PROGRAMME
! To cancel the drying programme, press
and hold the DRYING SELECTION
button for about 3 seconds.
WARNING:
Do not dry woollen garments or
articles with special padding (e.g.
quilts, quilted anoraks, etc.) and very
delicate fabrics. If garments are
drip/dry, load less items as to prevent
creasing.
WARNING:
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
!
22
8. AUTOMATIC
WASHING/DRYING
CYCLE
- Washing
! Open the drawer and put in the correct
amount of detergent.
! Refer to the list of washing programmes
for the fabrics to be washed (e.g. very
dirty cotton) and turn the selector knob to
the required programme.
! Adjust the wash temperature if
necessary.
! Press the option buttons (if required).
! Check that the tap is turned on and that
the discharge hose is positioned
correctly.
- Drying
! Select the degree of dryness that you
require choosing one of 3 automatic
programmes:
Extra dry programme (suitable for
towels, bathrobes and bulky loads).
Iron dry programme (that leaves the
laundry ready for ironing).
Cupboard dry programme (for
items that will be put away without
ironing).
! Press the START/PAUSE button.
! The programme selector remains in the
same stationery position throughout the
cycle until it ends.
! At the end of the wash phase the display
will show the drying time remaining.
! The washer dryer will then complete the
entire drying programme.
! The drying programme indicator will be
on, until the cool down phase begins and
the corresponding indicator is on.
! When the programme is finished the word
"End" will appear on the display. After 5
minutes the appliance will go into
standby mode (on certain models, the
display will show two lines).
! After the programme has finished please
wait for about 2 minutes until the DOOR
LOCKED indicator has gone out before
opening the door.
! Switch off the machine by turning the
programme selector to the OFF position.
! Open the door and remove the laundry.
! Turn off the tap.
CANCELLING THE DRYING PROGRAMME
! To cancel the drying programme, press
and hold the DRYING SELECTION
button for about 3 seconds.
You cannot exceed the maximum
dryable load of laundry indicated in
the programme table, otherwise the
laundry will not be dried satisfactory.
WARNING:
After cancelling the drying programme,
the cool down phase will begin and you
must wait for about 10/20 minutes
before opening the door.
!
EN
23
9. CUSTOMER SERVICE CENTRE AND WARRANTY
If you believe the washing machine is not working correctly, consult the quick guide
provided below with some practical tips on how to fix the most common problems.
Problem
Possible causes and practical solutions
The washing machine
does not work/start
Make sure it is correctly plugged in.
Make sure power is on.
Check whether the required program was correctly selected and to
have correctly started the machine.
Make sure the fuse has not blown and that the wall socket is working,
testing it with another appliance such as a lamp.
The porthole may not be correctly closed: open and close it again.
The washing machine
does not fill with
water
Make sure the water faucet is open.
Make sure the timer is correct set.
The washing machine
does not drain water
Make sure the filter is not clogged.
Make sure the drain hose is not bent.
Make sure there are no foreign objects in the filter.
Water leaked on the
floor near the washing
machine
This may be due to a leak in the gasket between the faucet and supply
tube; in this case, replace it and tighten the tube and faucet.
The washing machine
does not centrifuge
This could be due to the fact that water has not been completely
drained: wait a few minutes.
Some models include a "no centrifuge" function: make sure it is not on.
An excessive amount of detergent could prevent centrifuge: reduce the
amount at the next wash.
Strong vibrations are
heard during centrifuge
The washing machine may not be fully levelled: if necessary, adjust
the feet as indicated in the specific section.
Make sure transport brackets were removed.
Make sure the load is evenly distributed.
If a specific ERROR
appears of blinks
If error no. 0, 1, 5, 7 or 8 appears or blinks, contact the Customer
Service Centre directly.
If error no. 2 appears or blinks, the machine does not load water.
Make sure the water faucet is open.
If error no. 3 appears or blinks, the machine does not correctly drain.
Make sure the drain is free and that the drain hose is not bent.
If error no. 4 appears or blinks, the machine is too full. Close the
water faucet and contact the Customer Service Centre.
If error no. 9 appears or blinks, turn off the washing machine, wait 10
15 seconds and restart the program.
!
24
The use of ecological detergents without
phosphates may cause the following effects:
- cloudier rinse drain water: This effect is
tied to the suspended zeolites which do
not have negative effects on rinse
efficiency.
- white powder (zeolites) on laundry at
the end of the wash: this is normal, the
powder is not absorbed by fabric and
does not change its colour.
- foam in the water at last rinse: this
does not necessary indicate poor rinsing.
- abundant foam: This is often due to the
anionic surfactants found in the
detergents which are hard to eliminate
from laundry.
In this case, do not re-rinse to eliminate
these effects: it will not help at all.
If the problem persists or if you suspect a
malfunction, immediately contact the
Hoover Customer Service Centre.
You can also register for the Hoover
service plan to receive free home service
after the warranty expires.
Attention: the call is not toll-free. The cost
will be communicated in a voice message
by your telephone operator's customer
service.
Hoover recommends you always use
original spare parts available at our
Customer Service Centre.
The manufacturer declines all
responsibility for any printing errors in
the booklet included with this product.
Moreover, it also reserves the right to
make any changes deemed useful to its
products without changing their essential
characteristics.
Warranty
The product is guaranteed under the
terms and conditions stated on the
certificate included with the product. The
warranty certificate must be duly filled in
and stored, so as to be shown to the
Authorised Hoover Service Centre in
case of need.
Register your product!
Don’t waste time. Register your washing
machine at once, and discover the
benefits to which you are entitled.
Discover how at www.registerhoover.com
or by calling the number stated on the
related material.
hldsk
hldsk
hldsk
- WDXC -
15.06 - 41042936 - Canon Italia - Business Services Channel - Printed in Italy
6


Need help? Post your question in this forum.

Forumrules
1

Forum

hoover-wdxc-4751-dynamic-next-classic
  • The programme selector knob is out of synch by one turn, i.e. you have to select the programme AFTER the one you want to get the right one. Is there an easy way to correct this please? Submitted on 30-10-2021 at 17:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover WDXC 4751 Dynamic Next Classic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover WDXC 4751 Dynamic Next Classic in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info