594430

Hoover Max Extract 77 SpinScrub Manual

11
Zoom out
Zoom in
Previous page
1/30
Next page
11
Actual model may vary from images shown.
PICKING UP SPILLS
Your HOOVER
®
carpet cleaner may also be used to
pick up small liquid spills (one gallon or less,
never to exceed 1/8” in depth). Do not submerge
unit in liquid.
Place the floor nozzle with the SpinScrub
®
mode
selector to SPILL PICK-UP in front of the spill, pull
the nozzle very slowly over the spill.
CAUTION
! !
To reduce the risk of injury from moving parts,
unplug cleaner.
To prevent possible leaking, remove clean water tank
(Fig. 2.8) and Dirty Water Tank (Fig. 2.13). Set tanks
aside (do not set tank on furniture).
With handle in upright position, tilt cleaner back so
that handle rests on the floor.
3.4 Position the squeegee, larger lip facing up, on
bottom of nozzle until it snaps securely into place.
Make sure the outside edges are pushed up tight
against the nozzle.
Remove squeegee to return to cleaning carpets.
Read “Before you begin cleaning” instructions on
page 9.
CLEANING HARD FLOORS
How to Attach Squeegee for Hard Floor
Cleaning (Available on select models only)
Do not use the carpet cleaner on unsealed
hardwood floors.
To prevent damage to wood floors, follow
the flooring manufacturer’s cleaning
recommendations.
If using cleaner on sealed wood floors, inspect
floor surface for worn finish, bare wood or
separated joints. It is not recommended to use
the cleaner on wood floors if any of these
conditions exist.
3.4
1. Fill clean water tank according to instructions for
Fig. 2.9.
2. Fill detergent container with HOOVER
®
Hard Floor
Cleaner according to instructions for Fig. 2.10.
3. Slide SpinScrub selector to GENTLE SCRUB.
4. Dry hands and plug cleaner into a properly
grounded outlet.
5. Step on handle release pedal and lower handle to
operating position.
6. Set Wash/Rinse Setting switch to WASH (Wash/
Auto-Rinse™ when available). Turn cleaner on.
7. To release solution, press trigger. Slowly move
cleaner forward and backward over area to be
cleaned. Water and detergent will be released on the
forward stroke. For models with Auto-Rinse feature,
a water-only rinse will automatically be released on
the reverse stroke.
8. To pick up dirty solution, release trigger and slowly
move cleaner over area where solution has just been
dispensed. Use both forward and reverse strokes.
9. If rinsing the floor is desired, set Wash/Rinse
Setting switch to RINSE. Repeat steps 7 & 8. This
setting provides a water-only rinse in both the
forward and reverse strokes.
Rinsing is not necessary, but will help remove
detergent residue from the floor.
10. Empty recovery tank when the motor sound
becomes higher pitched and there is a loss in suction
(see “Automatic shut-off”, Fig. 2.19).
Continue>>
CAUTION
! !
CLEAN SURGE
®
BUTTON
(Available on select models only)
CAUTION
! !
Do not use the carpet cleaner to pick up
flammable or combustible liquids or chemicals.
CAUTION
! !
DO NOT USE THIS EXTRACTOR ON HARD
FLOORS UNLESS YOU HAVE THE PROPER
HARD FLOOR ATTACHMENT. USING THIS
MACHINE ON HARD FLOORS WITHOUT
PROPER ATTACHMENT MAY SCRATCH OR
DAMAGE YOUR FLOOR.
When finished picking up spills, follow “After
Cleaning” instructions.
The Clean Surge
®
button can be used to dispense
extra solution when cleaning particularly soiled areas
of carpet or spots.
To use, press Clean Surge
®
button while squeezing
solution trigger. For normal solution spray, release
button and continue to squeeze solution trigger.
11
La shampouineuse HOOVER
MD
peut également
servir à ramasser de petits dégâts liquides (un
gallon ou moins; ne jamais ramasser les dégâts de
plus de 1/8 po de profondeur) sur une moquette. Ne
pas plonger l’appareil dans un liquide.
Régler le sélecteur de mode SpinScrub
MD
en
position SPILL PICK-UP (ramassage de liquides
renversés), puis placer la buse pour plancher
devant le liquide renversé. Passer la buse très
NETTOYAGE DES PLANCHERS DURS
Pour prévenir les fuites, retirer le réservoir d’eau (fig.
2.8) et le réservoir de récupération (fig. 2.13). Mettre
les réservoirs de côté (ne pas les mettre sur un
meuble).
Mettre le manche en position verticale, puis
incliner l’aspirateur de façon à ce que le manche
repose au sol.
Lire les instructions de la section « Avant de
commencer le nettoyage » à la page 9.
Pour réduire les risques de blessures causées
par des pièces en mouvement, débrancher
l’appareil avant d’en effectuer l’entretien.
MISE EN GARDE
!
!
(Seulement sur certains)
MISE EN GARDE
!
!
Ne pas utiliser l’aspirateur sur les parquets
en bois dur non imprégné.
Pour éviter d’endommager les planchers en
bois, suivre les recommandations du fabri-
cant en matière de nettoyage.
Si vous utilisez l’aspirateur sur des planchers
en bois imprégné, en inspecter la surface pour
s’assurer qu’il ne présente pas un fini usé, des
parties non vernies ou des joints séparés. Il
n’est pas recommandé d’utiliser l’aspirateur
sur un plancher en bois présentant l’une de
ces conditions.
Continue>>
Installation du racloir pour le nettoyage
des planchers durs
3.4
3.4 Positionner le racloir, le grand rebord vers le haut,
au bas du suceur de manière à l’enclencher en
place. S’assurer que les côtés extérieurs sont
fermement appliqués contre le suceur.
Retirer le racloir pour reprendre le nettoyage de
moquettes.
BOUTON CLEAN SURGE
MC
(sur certains modèles)
Le bouton Clean Surge
MC
peut servir à appliquer une
quantité supplémentaire de solution pour le
nettoyage de taches tenaces ou de zones
particulièrement sales sur la moquette.
Pour utiliser cette fonction, appuyer sur le bouton
Clean Surge
MC
tout en serrant la gâchette pour
Le modèle d’aspirateur peut varier de
celui illustré.
Ne pas utiliser l’aspirateur Carpet
MC
pour
ramasser des liquides inflammables ou
combustibles ou des produits chimiques.
MISE EN GARDE
!
!
NE PAS UTILISER CET ASPIRATEUR
EXTRACTEUR SUR LES PLANCHERS À
SURFACE DURE À MOINS DE DISPOSER DE
L’ACCESSOIRE APPROPRIÉ. L’UTILISATION
DE CET APPAREIL SUR DES PLANCHERS À
SURFACE DURE SANS L’ACCESSOIRE
APPROPRIÉ PEUT ÉGRATIGNER OU
ENDOMMAGER LE PLANCHER.
MISE EN GARDE
!
!
l’application de solution. Pour la vaporisation normale
de la solution, relâcher le bouton et maintenir
enfoncée la gâchette pour l’application de solution.
RAMASSAGE DE LIQUIDES RENVERSÉS
lentement au-dessus du dégât liquide en ne faisant
qu’aspirer pour commencer.
Une fois terminé, suivre les instructions de la
section « Après le nettoyage ».
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover Max Extract 77 SpinScrub at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover Max Extract 77 SpinScrub in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info