594565
12
Zoom out
Zoom in
Previous page
1/15
Next page
10
Pull Unicouple and its hoses completely out from storage compartment located at rear of dishwasher
and attach it to the faucet adapter.
Turn water fully on before starting the dishwasher.
3
1
Turn off the water.
Release the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
room, from severe splashing.
Release Unicouple from faucet by depressing the collar at the top of the Unicouple connector.
3
2
1
Remove the power cord plug from the wall receptacle.
Disconnect Unicouple from faucet adapter.
2
1
If faucet has not threads: attach the faucet adapter to faucet, then tighten every screw
of the adapter. To prevent leaking your should tighten the adapter.
2
Attach the Unicouple connector to the faucet adapter by depressing the collaratthetopoftheconnector.
When Unicouple is all the way up onto the adapter, release the collar. It willthensnapIntopositionto
lock the Unicouple in place. The Unicouple s small hose carries water from the faucet to the dishwasher.
Its large hose carries drain water to the sink. Be sure Unicouple is pointing toward the sink bowl drain
opening and the sink drain is open for water that will drain from your dishwasher. If your dishwasher
drains into a disposer, operate the disposer until it is completely empty before starting the dishwasher.
'
Connector of ModelⅠ
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is
recommended thet the hose be disconnected and the hole plugged.
Fused electrical supply is required-copper wire only. Time delay fuse or circuit breaker recommended and provide separate
circuit serving only this appliance. Outlet should be placed in adjacent cabinet.
Make sure that the plug on the appliance remains accessible after installation.
After making sure that the voltage and the frequency values for the current in the home
correspond to those on the rating plate and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into an electrical socket which is
earthed properly. If the electrical socket to which the appliance must be connected is not
appropriate for the , replace the socket ,rather than
using a adaptors or the like as they could cause overheating and burns.
plug (installed by a qualified electrician)
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure is below theminimum
consult our Service Department for advice.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover HEDS 668-80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover HEDS 668-80 in the language / languages: English as an attachment in your email.

The manual is 2,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info