817773

Hoover HAHG74S2X Manual

10
Zoom out
Zoom in
Previous page
1/98
Next page
1. As illustrated, assemble parts in sequence:
2. Tighten the joints with the spanner, remembering
to twist the pipes into position.
IMPORTANT: carry out a final check for leaks on
the pipe connections using a soapy solution.
For some models a conic link is furnished to
outfit for the installation in the countries where
this type of link is obligatory; in picture 8 it is
pointed out how to recognize the different
types of links (CY = cylindrical, CO = conic). In
every case the cylindrical part of the link has to
be connected to the hob.
The flexible tube shall be fitted in such a way that
it cannot come into contact with a moveable
part of the housing unit (e.g. a drawer) and does
not pass through any space where it may
become crushed/ kinked or damaged in any
way.
B: 1/2 Seal
A: 1/2 Male Adaptor Cylindirical
C: 1/2 Female Gas Adaptor Conical-Cylindirical
3. Attach fitting C to mains gas supply using rigid
copper pipe or flexible steel pipe.
When connecting the hob to the gas supply via
use offlexible hoses please ensure that the
maximum distance covered by the hose does
not exceed 2 metres.
To prevent any potential damage to the hob
please carry out the installation following this
sequence (Figure 6*):
or Cylindirical-Cylindirical
NEVER USE A FLAME. Also, make sure that the
flexible pipe cannot come into contact with a
moving part of the cabinet (eg.adrawer) and that
it is not situated where it could be damaged.
Warning: If gas can be smelt in the vicinity of this
appliance turn off the gas supply to the
appliance and call the engineer directly. Do not
search for a leak with a naked flame.
ADAPTING THE HOB TO DIFFERENT TYPE
OF GAS
To adapt the Hob for use with different types of
gas, carry out the following instructions:
• Remove the grids and burners
• Unscrew the injector and replace it with one
suitable for the gas to be used (see gas type
table)
burner support (Figure 7*)
• Insert on hexagonal spanner (7 mm) into the
REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob
to the minimum setting and then remove the
knob (this can easily be removed by applying
gentle pressure).
Turning the screw clockwise reduces the gas
flow, whilst turning it anticlockwise increases
the flow – Use this adjustment to obtain a flame
of approximately 3 to 4 mm in length and then
replace the control knob.
Using a small «Terminal» type screwdriver the
regulating screw can be adjusted as in Figure 9*.
When the gas supply available is LPG - the
screw to set the idle flame must be turned
(clockwise) to the end stop.
When you have carried out the new gas
regulation, replace the old gas rating plate on your
appliance with one (supplied with hob) suitable for
the type of gas for which it has been regulated.
*See “Technical information” section at the end of this manual.
EN 9
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover HAHG74S2X at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover HAHG74S2X in the language / languages: English, German, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2.9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info