594383
5
Zoom out
Zoom in
Previous page
1/70
Next page
CLEANER MAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator in the container empty the dust bin.
IMPORTANT: To maintain optimum performance do not allow the dust to sit higher than
the max level.
1. Release the container by sliding the dust container release button towards the rear of
the cleaner. Lift the dust container from the cleaner main body. [14]
2. Hold the dust container over a bin with one hand and use the other hand press the
Dust Container Door Release Button. [15]
3. Close the Dust Container door and refit to the cleaner main body.
Cleaning the washable filters
The cleaner is fitted with a blue filter pack. To maintain optimum cleaning performance
regularly remove the the filters and tap against the side of the bin to release dust. The
filters should be washed after 5 container empties or when the filter has excessive dust
level.
IMPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
IMPORTANT: Regularly check and maintain the filters by following the filter
maintenance instructions , it is also recommended that you purchase new filters after
every 3rd filter wash. This will maintain your cleaners performance.
IMPORTANT: Always ensure the filters are fully dry before use.
To access the pre-motor filter:
1. Release the container by sliding the dust container release button towards the rear of
the cleaner. Lift the dust container from the cleaner main body. [14]
2. Hold the dust container with one hand and with the other hand rotate the bin handle
anti clockwise to release it from the dust container. [16]
3. Remove the blue filter pack located in the dust container handle. [17]
4. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [18]
5. Reassemble to filter pack once fully dry and refit to the cleaner.
IMPORTANT: Do not use the product without the filter pack fitted.
*Certain Models Only ** Certain models only, nozzles may vary according to model
To access the exhaust filter:
1. Release the container by sliding the dust container release button towards the rear of
the cleaner. Lift the dust container from the cleaner main body. [14]
2. Unclip the exhaust filter cover from the dust container cradle on the cleaner main
body. [19]
3. Using the tab remove the exhaust filter from the cleaner main body. [20]
4. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [21]
3
GB
Furniture Nozzle – For soft furniture and fabrics. [13]
Parquet Nozzle* – For parquet floors and other delicate floors. [1U]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal. [1V]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal. [1W]
Grand Turbo Nozzle* - Use the turbo nozzle for deep cleaning on carpets. [1X]
IMPORTANT: Do not use the grand turbo and mini turbo nozzles on rugs with long fringes,
animal hides and carpet pile deeper than 15mm. Do not keep the nozzle stationary while
the brush is rotating.
Cleaning the dust container / multi-cyclonic separation unit
This cleaner uses a multicyclonic separation system, unique to Hoover. If necessary the
separation unit can be disassembled from the dust container and cleaned.
1. Release the dust container by sliding the dust container release button towards the
rear of the cleaner. Lift the dust container from the cleaner main body. [14]
2. Hold the dust container with one hand and with the other hand rotate the dust
container handle anti clockwise to release it from the dust container. [16]
3. Remove the multicyclonic separation unit from the dust container by pulling the
handle provided. [22]
4. If necessary, use a cloth to remove excessive dust from the multi-cyclonic unit surface.. [23]
5. Reassemble the multicyclonic separation unit to the dust container and refit the filter
pack in position.
6. Reassemble the dust container handle to the bin container. Refit the dust container to
the cleaner.
Note: For stubborn dirt the multi-cyclonic separation unit, or the dust container can be washed,
but care must be taken to ensure that both are completely dry before use.
Important: For optimum performance, we recommend that the multi-cyclonic separation
system is inspected after each empty.
Removing a blockage from the cleaner
1. Check if the dust container is full. If so refer to ‘Emptying the dust container.
2. If the dust container is empty but suction is still low:
A. Do the filters need cleaning? If so refer to ‘Cleaning the washable filters.
B. Check if there is any other blockage in the system - Use a rod or pole to remove any
blockage from the extension tube or flexible hose.
C. Check if pre-motor filter is fitted.
D.
Check if the separation unit needs to be cleaned. Refer to ‘Cleaning the separation unit’
USER CHECKLIST
Should you have a problem with the product, complete this simple user checklist before
calling your local Hoover service.
•  Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
•  Is the dust bag over-lled? Please refer to ‘Cleaner Maintenance’.
•  Is the lter blocked? Please refer to ‘Cleaner Maintenance.
•  Is the hose or nozzle blocked? Please refer to ‘Removing a blockage from the system.
•  Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically reset.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover Curve at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover Curve in the language / languages: All languages as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info