705451

Hoover ATDH11A2TKERXM-S Manual

114
Zoom out
Zoom in
Previous page
1/124
Next page
ES
7. CONTROLES E INDICADORES
7
6
5
4
3
2
1
BD
E
F
A
C
A - Selector de programa - Es posible selec-
cionar el programa de secado deseado girando
el selector en ambas direcciones. Para cancelar
las selecciones o apagar la secadora, gire el
selector a la posición OFF.
B - Dígito en pantalla - La pantalla muestra el
tiempo restante para completar el secado, el
tiempo pospuesto en caso de selección de inicio
diferido y otras configuraciones de notificaciones.
C - Botones -
1. Botón Inicio/Pausa
Para iniciar el programa seleccionado y/o
suspenderlo.
2. Botón de inicio diferido
Permite retrasar el inicio del programa de 1 a
24 horas en intervalos de 1 hora. El retraso
seleccionado se muestra en la pantalla.
Después de presionar el botón INICIO, la hora
mostrada disminuye una hora tras otra.
Si se abre la puerta con el inicio diferido confi-
gurado, después de volver a cerrar la puerta,
vuelva a pulsar el botón de inicio para reanudar
el conteo.
3. Botón de selección de secado
Permite establecer la opción editable de nivel de
secado deseado hasta 5 minutos después del
inicio del ciclo:
Lista para plancha: deja las prendas ligera-
mente húmedas para facilitar el planchado.
Secado tendal: para que las prendas estén
listas para tenderlas.
Secado guardar: para ropa que se puede
guardar directamente.
Extra seco:
para obtener prendas comple-
tamente secas, ideal para carga completa.
Este electrodoméstico está equipado con la
función Gestor de secado. En ciclos automáticos,
cada nivel de secado intermedio antes de llegar
al seleccionado se indica mediante el parpadeo
del indicador luminoso correspondiente al grado
de secado alcanzado. En caso de incompati-
bilidad, todos los LED parpadean rápidamente
3 veces.
4. Botón Rápido/Selección del ciclo de tiempo
Es posible cambi
ar algún programa automático
al programa RÁPIDO hasta 3 minutos después
del inicio del ciclo. La presión progresiva aumenta
el tiempo (30-45-59 minutos).
Después de esta selección, para restablecer el
funcionamiento de secado automático es nece-
sario apagar la secadora. En caso de incompati-
bilidad, todos los LED parpadean rápidamente
3 veces.
Es posible transformar un ciclo de automático a
programado hasta 3 minutos después del inicio
del ciclo.
La presión progresiva aumenta el tiempo en
intervalos de 10 minutos. Después de esta selec-
ción, para restablecer el funcionamiento de secado
automático es necesario apagar la secadora.
En caso de incompatibilidad, todos los LED
parpadean rápidamente 3 veces.
5. Antiarrugas
Esta opción permite activar un movimiento
antiarrugas del preciclo del tambor en caso de
activación del retraso y al final del ciclo de se-
cado. Se activa cada 10 minutos, hasta 6 horas
después
del final del ciclo de secado. Para
detener los movimientos, ajuste el selector a la
posición OFF. Resulta útil cuando no es posible
sacar inmediatamente la ropa del electrodo-
méstico.
6. Memoria
Esta opción permite guardar las opciones confi-
guradas en un ciclo.
MEMORIZACIÓN:
cuando se esté ejecutando
el ciclo, pulse el botón "memoria" durante tres
segundos. La luz de control de la opción
"memoria" parpadea tres veces y guarda las
opciones de configuración vinculadas al ciclo
seleccionado.
RECUPERACIÓN
: después de seleccionar el
ciclo, pulse el botón "memoria" para recuperar
las opciones guardadas (no el ciclo).
7. Bloqueo de teclas
Esta función permite bloquear cambios no de-
seados de las opciones establecidas durante la
fase de secado.
Acti
vación/desactivación: presione los botones
3 y 4 simultáneamente durante dos segundos.
El signo "LOC" aparecerá en pantalla. Al desblo-
quear la opción, en la pantalla aparece el signo
"Unl", solo una vez.
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
12
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
7. CONTROLS AND INDICATORS
7
6
5
4
3
2
1
A - Programme Selector - Rotating the knob in
both directions it's possible to select the desired
drying program. To cancel the selections or
switch off the dryer rotate the knob on OFF.
B - Display Digit - The display shows the
remaining time for drying, the postponed time in
case of delayed start selection and other
notifications setting.
C - Buttons -
1.Start/Pause Button
To start the selected program and/or suspend it.
This appliances is equipped with Drying Manager
Function. On automatic cycles, each level of
intermediate drying, prior to the reaching the
selected one, is indicated by flashing the light
indicator corresponding to the degree of drying
reached. In case of incompatibility, all LEDs flash
quickly for 3 times.
4.Rapids Button / Time Cycle selection
It's possible switch some automatic programs to
RAPID programs, up to 3 minutes after t
he start of
the cycle. The progressive pressure increases
the time (30-45-59 minutes).
After this selection to reset the automatic drying
functioning is necessary to switch off the dryer.
In case of incompatibility, all LEDs flash quickly
for 3 times.
It's possible transform a cycle from automatic to
programmed, up to 3 minutes after the start of
the cycle.
The progressive pressure increases the time in
10-minute intervals. After this selection to reset
the automatic dying functioning is necessary to
switch off the dryer. In case of incompatibility, all
LEDs flash quickly for 3 times.
5.Anti Crease
This option allows to activate an anti-creases
movement of the drum pre cycle in case of
activation of the delay and at the end of drying
cycle. It is activated every 10 minutes, up to 6
hours after the end of the drying cycle. To stop
the movements set the knob to OFF. Useful
when it's not possible to remove immediately the
laundry.
6.Memory
This option allows you to store the options set on
a cycle.
MEMORY: when the cycle is running push the
button "memory" for three seconds. The control
light "memory" flashes for three times and stores
the set options connected to the cycle selected in
the flange.
RECALL: after the selection of the cycle push
the button "memory" for recall the stored options
(not the cycle).
7. Keylock
This function allows to block unwanted changes
of the set options on the bezel, during drying
phase.
Activation/Inactivation: push 3 and 4 buttons
simultaneously for two seconds. The sign "LOC"
appears on the display. Unlocking the option, on
the display appears the sign "Unl", only once.
B
C
D
E
F
2.Delay Start Button
It allows to delay the start of the program from 1
to 24 hours in 1-hour intervals. The delay
selected is shown on the display.
After pressing the START button the time
showed decrease hour after hour.
Opening of the porthole with delayed start set,
after re-
to resume the counting.
3.Drying Selection Button
It allows to set the desired dryness level editable
option up to 5 minutes after the starting of the cycle:
Ready to Iron: It leaves the garments slightly wet
to facilitate ironing.
Dry Hanger: To get garment ready to be hang.
Dry wardrobe: For laundry that can be directly
stored.
Extra-dry: To get completely dry garments,
ideal for full load.
A
closing the porthole, press START again
Si pulsas esta tecla, es posible reducir la
velocidad máxima, y si lo deseas, puedes
cancelar el ciclo de centrifugado.
velocidad de giro cancelada.
Si la etiqueta no proporciona información
específica, significa que se puede usar el
centrifugado máximo previsto por el
programa.
Para reactivar el ciclo de centrifugado,
pulsa la tecla hasta alcanzar la velocidad
de centrifugado deseada.
Es posible modificar la velocidad de
centrifugado sin detener la lavadora.
Esta opción le permite cambiar la
temperatura de los ciclos de lavado.
lavado en frío.
No es posible elevar la temperatura por
encima del máximo permitido para cada
programa, con el fin de proteger los
tejidos.
Esta opción le permite pre-programar el
ciclo de lavado para iniciarlo con una
posterioridad de hasta 24 horas.
Para diferir el inicio del ciclo:
- Introduzca el programa deseado.
- Pulse el botón una vez para activarlo
(h00 aparece en la pantalla) y luego
pulse de nuevo para fijar un intervalo de
1 hora (h01 aparece en la pantalla). El
retardo preestablecido aumenta en 1
hora cada vez que se pulsa el botón,
hasta que aparezca h24 en la pantalla,
y en ese momento, al pulsar el botón de
nuevo, se restablecerá el inicio diferido
a cero
-
Confirme pulsando la tecla INICIO/PAUSA
(
la luz en la pantalla comienza a
parpadear). La cuenta atrás comienza y
cuando termina el programa se iniciará
automáticamente.
Es posible cancelar el inicio diferido
girando el selector de programas a la
posición APAGADO.
Si hay alguna interrupción en el
suministro de energía mientras la
lavadora está en funcionamiento, una
memoria especial almacena el programa
seleccionado y, cuando se restablezca la
energía, continúa donde lo dejó.
Las opciones y funciones se debe
seleccionar antes de pulsar la tecla
INICIO/PAUSA.
Si se selecciona una opción que no es
compatible con el programa elegido
entonces el indicador opción parpadea
primero y luego se apaga.
Tecla SELECCIÓN CENTRIFUGADO
Para evitar dañar los tejidos, no es
posible aumentar la velocidad por
encima del máximo permitido para
cada programa.
Una cantidad excesiva de detergente
puede provocar un exceso de
espuma. Si el electrodoméstico
detecta la presencia de una cantidad
excesiva de espuma, puede descartar
la fase de centrifugado, o extender la
duración del programa y aumentar el
consumo de agua.
La lavadora está equipada con un
dispositivo electrónico que descarta el
ciclo de centrifugado si la carga está
desequilibrada. Esto reduce el ruido y
la vibración en la lavadora, y prolonga
la vida de la lavadora.
Tecla SELECCIÓN TEMPERATURA
Tecla INICIO DIFERIDO
114
… 114 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hoover ATDH11A2TKERXM-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hoover ATDH11A2TKERXM-S in the language / languages: German as an attachment in your email.

The manual is 28,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info