Manual Hoonved ST 60E (page 14 of 20) (English)

637677

Zoom out

Zoom in

1/20

ENGLISH

Part 2: For the operator

When the CHECK LED switched OFF, the

regeneration cycle is nished.

The machine is now ready for use again.

ATTENTION

Programming of cycles for the start-up of regeneration

should be carried out by authorised technicians only (see

Part 3: Reserved for technicians, paragraph 3.2 Setting

cycles for REGENERATION PROMPT).

2.2 CLEANING (Fig. 10)

2.2.a General information

Strict compliance with the maintenance instructions in this

section will keep your machine in a good working condition

and will notably reduce the need for repairs.

ATTENTION

If any machine component becomes faulty, FIRST CHECK

that all the instructions given in the previous paragraphs

have been complied with during use.

Repairs must be carried out immediately, as soon as the

fault occurs. This will prevent the trouble from becoming

worse and damaging other parts.

ATTENTION

Daily operations to carry out when work has ended, with

the machine OFF , the main circuit-breaker disconnected,

the water cocks off and the washing tub empty.

1. Thoroughly clean the inside parts of the machine.

2. Remove the suction protection (23).

3. Remove the lter (22) from the bottom of the machine

by releasing the overow (21).

4. Wash the lters under running water and t them cor-

rectly back in their housings.

ATTENTION

Frequently check and clean the spraying units, removing

them from their housings and eliminating any dirt and

fouling. The frequency with which this operation must be

carried out depends on the quantity of dirt or on the unsa-

tisfactory washing results. Never use corrosive products

like sodium hypochlorite (bleach) or hydrochloric acid, wire

wool or steel brushes to clean either the inside or outside

parts of the machine.

2.3. PREVENTION MAINTENANCE (Fig. 10)

The preventive maintenance operations must be carried

out with the machine OFF, the main circuit-breaker di-

sconnected, the water delivery cocks off and the washing

tub empty.

2.3.a Checking and cleaning the spray arms and

nozzles (Fig. 10)

Periodically check to make sure that the lower washing

arm and rinsing arm (24/25) and their relative nozzles are

not clogged (26/27).

Cleaning the lower/upper unit

1. Unscrew the ring nut and lift the arm (24/25).

2. Wash the washing and rinsing arm.

If the nozzles (27) are clogged, unscrew them to de-

mount and clean, taking care to prevent the shape of

the nozzle from being deformed. After cleaning, t the

nozzles exactly back in their original positions.

3. Remount all parts by complying with the above in-

structions in reverse.

2.4 DESCALING

Where hard water is present lime scale deposits will for

in the machine and on dishes, which must, for reasons

of hygiene, be removed by descaling.

Advice on operation procedures and frequency for this

treatment are generally given by the detergent supplier,

who can provide suitable products.

In order to avoid damaging the machine, do not

exceed recommended doses, follow the detergent

producer’s directions scrupulously and, having

nished operations, rinse thoroughly.

2.5 TEMPORARY STOPPAGE

If the machine is to be left inactive for a period of some

weeks, it is advisable beforehand to load the tank and

run a few empty cycles with clean water then drain, so

as to avoid the formation of unpleasant odours.

If necessary, repeat the process several times until the

water is still clean after washing.

If the stoppage is to be very long, it is advisable to

drain the water from the boiler and from the electric

pump.

2.6 DEMOLITION and DISPOSAL

When the machine is to be scrapped, drain the water

from the tank and from the boiler, as indicated in the

points above, and disconnect the machine from the

water and electricity supply networks, then dispose of

the components according to current regulations, re

specting national and local ecological and environmetal

legislation, and taking care to separate the parts as

follows:

- metallic parts: body work, surfaces, panels, lters;

- electrical parts: motors, remote switches, micro-

switches, cabling;

- plastic parts: connectors, baskets;

- rubber parts: tubes, couplings

2.7 SCHEDULED MAINTENANCE

It is advisable to subject the machine to scheduled

maintenance every 6 months.

The producer declines all responsibility for any

printing errors contained in this booklet.

The instructions, drawings, tables and everything else

in this manual are of a condential technical nature.

For this reason, none of the information may be either

completely or partially duplicated or disclosed to

third parties without prior written authorization from

HOONVED which is the sole proprietor and which

reserves the right to make any modications as may

be considered necessary without advance warning.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hoonved ST 60E in the language / languages: English as an attachment in your email.

The manual is 1,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hoonved ST 60E

Hoonved ST 60E User Manual - German - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hoonved ST 60E Manual

Product: