Manual Hoonved ST 48E (page 13 of 20) (English)

637675

Zoom out

Zoom in

1/20

ENGLISH

Part 2: For the operator

2.1.e.1Manual draining for mach. with drainage pump

For machines tted with a drainage pump it is possible

to empty the tank by carrying out the manual draining

cycle, during which only the drainage pump remains

active.

IMPORTANT

This cycle can only be carried out by leaving the ma-

chine SWITCHED ON with the tank full of water and the

door OPEN.

Having released the overow, press and hold the

START (S3) button until the LED LC2 and CHECK

together) begins to FLASH, and then release the

START (S3) button;

The DRAINAGE CYCLE will begin.

IMPORTANT

By pressing the START (ST) button or switching

the power switch (Q1) to OFF, you can interrupt the

drainage cycle before the preset time is up;

to restart the interrupted cycle, press START (S3)

again.

When the LC2 LED lights up CONSTANTLY,

the drainage cycle is nished.

At the end of the cycle, restore the lters (22/23) and the

overow (21) to their respective positions.

2.1.f Self-washing and draining

At the end of the washing operations SWITCH OFF the

machine pressing the switch (Q1)

After having unlocked the overow pipe, close the door

of tank access , press push button START (S3) (about

5 sec.)

The cycle Self-washing and draining will start ; Led LC1

and LC3 will light, while led CHECK is FIXED ON, with

draining pump ON (for the machines equipped with).

The end of the described phase is indicated by the switch-

ing OFF of the Led CHECK,

2.1.g Cold rinsing (optional)

With machine ON (switch line Q1 is ON ), tank full of

water and door closed (LC1 or LC2 or LC3 and CHECK

= FIXED ON)

keep pressed regeneration button (S4) to make the cold

rinsing of the crockeries for all the wished time.”

2.1.h Switching off at the end of the day

At the end of the working day SWITCH OFF the ma-

chine by pressing the power switch (Q1) into the

OFF position.

Switch off the mains switch feeding the machine

and close the water supply taps.

For any repairs, contact only assistance centres au-

thorised by the manufacturer.

Warnings during the operation

1) Ensure that the washing temperature remains at

approx. 55-60°C;

2) Avoid immersing bare hands in the detergent-lled

water; if this should happen, rinse immediately and

thoroughly with running water;

3) Use only anti-foaming detergents, specics for use in

industrial machines;

4) Deactivate the machine in case of break-down or

malfunction.

For any repairs, contact only assistance centres autho-

rised by the manufacturer, and insist on the use of

original parts.

5) In no case should you change the the original for-

mulations without rst consulting an authorised

assistance centre;

6) When the machine is operating, do not open the door

too rapidly.

7) Wash tank water should be changed at least twice a

day or according to daily wash requirements.

Failure to follow the above warnings may compromise

the safety of the washing machine.

Useful advice for better washibg results

Any unsatisfactory results from washing can be seen

when traces of dirt are left on dishes or other items; any

water marks may be caused by insufcient rinsing.

In this case, ensure that the rinsing nozzles (27) are

clean and that there is pressure in the water system.

If there are traces of waste, ensure that:

- The lters (22/23) are clean;

- the water temperature is around 55-60°C;

- items are correctly positioned in the basket;

- the washing/rinsing nozzles are clean (26/27);

- the arms (24/25) rotate freely.

2.1.i RESIN REGENERATION OPERATION

(for model D only)

We recommend that you carry out regeneration when all

work is nished.

First of all, ensure that there is coarse cooking salt in the

salt container, and proceed as follows:

1. unscrew the salt container plug and pour in 1 Kg of

coarse salt.

2.Screw the plug down tight, to ensure that the container

is completely sealed.

On reaching the set number of cycles, the CHECK LED

will ash;

this indicates that it is time to carry out regeneration.

The signal that the set number of cycles has been reached

can only be deactivated by starting the regeneration cycle

(regenerate button (S4)).

REGENERATION OPERATIONS

With the machine SWITCHED OFF (the power switch

(Q1) in the OFF position), and the tank EMPTY (release

the overow) and the door CLOSED, press and hold the

regenerate button (S4) (Fig. 1/ 9), until the CHECK LED

FLASHES.

The REGENERATION CYCLE will begin, and the

CHECK LED will ash continuously.

The machine will now automatically carry out all the ne-

cessary operations for a MAXIMUM of 20 mins, during

which the machine cannot be used.

ATTENTION

Opening the door during the cycle will stop the regenera-

tion cycle; the CHECK LED will start to ash RAPIDLY;

on closing the door the cycle will resume from where it

was stopped.

C I II III

LC1LC2LC3

CHECK

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Hoonved ST 48E in the language / languages: English as an attachment in your email.

The manual is 1,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Hoonved ST 48E

Hoonved ST 48E User Manual - German - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Hoonved ST 48E Manual

Product: