613691
29
Zoom out
Zoom in
Previous page
1/34
Next page
29
Troubleshooting Guide
This is a quick guide to help you diagnose and cope with possible problems with
your wireless control system. For further assistance, please contact your Installer.
Symptom Possible Cause Remedy
ST9420C has a blank LCD
display
No power to the
heating system.
Check that there is power to the
heating system.
Fault in ST9420C Call Installer
ST9420C indicates that
Heating and/or Hot Water
are ON, but radiators are
cold and/or taps are running
with cold water.
Temperature controls
are switched off or
set too low.
Check that the temperature
controls in the system are set to
appropriate levels.
Boiler or other
system controls
have malfunctioned.
Call Installer
ST9420C shows the
message:
‘INTERNAL FAULT’
Fault in ST9420C Call Installer
Every few seconds, the
ST9420C screen shows the
message:
ST9420C is
counting down the
number of days
until your next boiler
service is due.
Arrange a boiler service before
the counter reaches zero.
After servicing your boiler, the
Service Engineer / Installer will
reset the ST9420C to remind
you when the next boiler service
is due. Each service is normally
a maximum of 1 year apart.
Although the heating is still
operating, the ST9420C
screen keeps flashing the
message:
Your boiler service
is overdue.
Arrange an immediate boiler
service.
After servicing your boiler, the
Service Engineer / Installer will
reset the ST9420C to remind
you when the next boiler service
is due. Each service is normally
a maximum of 1 year apart.
Can I override the Programmer from the DT92E thermostat?
As well as changing the set temperature from the DT92E, it is also possible to override
the heating system on or off from the DT92E. This is only possible if the ST9420C is in
AUTO or ONCE Modes. If ST9420C is in CONT mode it will not be possible to switch
the heating off from the DT92E. Similarly, if ST9420C is in OFF mode, it will not be
possible to switch the heating on from the DT92E. If these latter overrides are required
it is first necessary to change the ST9420C mode setting to AUTO or ONCE.
FAQ AND TROUBLESHOOTING
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Y9420S Sundial RF2 Pack 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Y9420S Sundial RF2 Pack 3 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info