613691
7
Zoom out
Zoom in
Previous page
1/34
Next page
7
GETTING STARTED WITH YOUR ST9420C
b. To change the day of the month, press the or buttons until the correct
day is shown. Each press of the button will change the date by one day. As soon
as a change has been made, the message ‘IS DAY OK?’ will be displayed. Once
the correct day is reached, press the green button to confirm, and move to
the next step. If you do not need to make a change, just press the button
immediately and this will move you to the next step.
c. The month digits will now be flashing and ‘SET THE MONTH’ will be displayed. To
change the month, press the
or buttons until the correct month is shown.
The message ‘IS MONTH OK?’ will be displayed. Press the green button to
confirm the month is correct and move to the next step.
d. The year digits will now be flashing and ‘SET THE YEAR’ will be displayed. To
change the year, press the
or buttons until the correct year is shown. The
message ‘IS YEAR OK?’ will be displayed. Press the green button to confirm
the year is correct. If you have made a change and the date is a valid date, the
message ‘DATE SAVED’ will show, and you can move to the next step. If the date
you set was not valid, for example 31 September, the message ‘INVALID’ will
show and you will be returned to the start of the date setting operation.
e. The time will now be flashing and the message ‘SET THE TIME’ will be displayed.
To change the time, press the
or buttons until the correct time is shown.
Each press of the button will change the time by one minute. Holding the button
down for more than a few seconds will change the time slowly at first, then
quickly. The message ‘IS TIME OK?’ will be displayed. Press the green button
to confirm the time is correct. If you have made a change, the message ‘TIME
SAVED’ will show, followed quickly by ‘DATE + TIME COMPLETE’.
f. Move the slider to the RUN position to complete setting the date and time.
Note: if the slider is moved at any time before the date and time have been set
correctly, the message ‘DATE UNCHANGED’ will be displayed briefly, and your
changes will not be saved.
Step 2: Running a Built-in Programme
With the date and time correct, your ST9420C Programmer will now be operating
to the built-in programmes. These have been designed to provide heating and hot
water at typical times throughout the day, but if you want to customise the settings,
please see the next section ‘PROGRAMMING YOUR ST9420C’ (page 8).
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Y9420S Sundial RF2 Pack 3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Y9420S Sundial RF2 Pack 3 in the language / languages: English as an attachment in your email.

The manual is 1,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info