585058

Honeywell T8600D - Chronotherm IV Manual

16
Zoom out
Zoom in
Previous page
1/28
Next page
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
16
M10342
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time
Wake
Leave
Return Sleep
Day
Heat/Cool
Settings
Daylight
Time
Copy
Outdoor
HEATING
COOLING
PERCENT LOAD
TEMPERATURE
THERMOSTAT
HEAT SETPOINT
P+I CONTROL
POINT
PROPORTIONAL COOL
CONTROL POINT
THERMOSTAT
COOL SETPOINT
P+I CONTROL POINT
PROPORTIONAL HEAT
CONTROL POINT
M4414
100 50 0 50 100
Fig 13. Proportional temperature control versus P+I
temperature control.
Operation Sequence
The thermostat energizes specific terminals depending what
the Fan and System are set to. The LCD will display the time,
room temperature, system and fan selection. Symbols will be
displayed when the heating, cooling or fan is energized. See
Table 10 for specific information.
NOTE: Not all the thermostat models have all the terminals
listed in the Energize column.
Table 10. Conventional System Sequence of Operation.
Using Daylight Savings Time Feature
This feature allows you to change in and out of Daylight
Savings Time with a key press. When the Daylight Time Key is
pressed in the fall, the time will go back one hour. In the
spring, the time will go ahead one hour and the display will
show DST. See Setting the Current Day and Time section for
initial setting instructions.
NOTE: Pressing the Daylight Time Key more than once
within a five minute period will scroll you through
various time options (Example: one hour earlier or
later with or without DST). Pressing the Daylight
Time Key six times in a five minute period will return
you to your original settings.
Displaying the Outdoor Temperature
If your thermostat is equipped with an outdoor sensor, you
can check the temperature at the sensor by pressing i
once.
OPERATION
P+I Control
The thermostat microprocessor based control requires that
the user understands temperature control and thermostat
performance. A conventional electromechanical or electronic
thermostat does not control temperature precisely at setpoint.
Typically, there is an offset (droop) in the control point as the
system load changes. This is a phenomenon that most people
in the industry know and accept. Many factors contribute to
offset including switch differential, thermal lag, overshoot,
cycle rates and system load.
The thermostat microprocessor simultaneously gathers,
compares and computes data. Using this data, it controls a
wide variety of functions. The special proprietary algorithm
(program) in the thermostat eliminates the factors causing
offset. This makes temperature control more accurate than
the conventional electromechanical or electronic thermostats.
The temperature control algorithm is called proportional plus
integral (P+I) control.
The thermostat sensor, located on the thermostat or remote,
senses the current space temperature. The proportional error
is calculated by comparing the sensed temperature to the
programmed setpoint. The deviation from the setpoint is the
proportional error.
The thermostat also determines integral error, which is a
deviation based on the length of error time. The sum of the
two errors is the (P+I) error. The cycle rate used to reach and
maintain the setpoint temperature is computed using the P+I.
The addition of the integral error is what differentiates the
thermostat from many other electronic and electromechanical
thermostats. See Fig. 13.
Equipment Protection
As part of the operational sequence, the thermostat
microprocessor also incorporates minimum off time for all
cooling stages. Using the minimum off time assures that rapid
cycling of equipment does not occur, which extends
equipment life. Minimum off times are set in the Installer
Setup.
Selection
Fan System Call Energize Display
Auto Off None None None
On Off None G
Auto Cool None O None
Auto Cool or Auto Cooling O, G and Y
and
Auto Heat None B None
Auto Heat or Auto Heating B and W
a
Auto Auto None O or B
b
None
a
When electric heat fan is selected, G is energized and fan
symbol is displayed.
b
Based on last piece of equipment called (cooling = O or
heating = B) and Installer Setup selection.
M10341
Time Set Program
System Fan
Run
Program
Hold Temp
Set Current
Day/Time
Wake
Leave
Return Sleep
Day
Heat/Cool
Settings
Daylight
Time
Copy
Daylight
Time
Auto
System Fan
Wake
Room
AM
Tue
Heat
… 16 …


Need help? Post your question in this forum.

Forumrules
1

Forum

honeywell-t8600d---chronotherm-iv

Reset search

  • The AC is not working. The repair person via a phone call said to turn off the system. How do I do this?
    I read the Manuel.
    The fuse is fine.
    Submitted on 28-7-2022 at 20:15

    Reply Report abuse

  • An HVAC repair person cannot come until next week. The AC is not working.
    He suggested I turn off the system. How do I do this? I read the manuel.
    It is not a problem with the fuse. Submitted on 28-7-2022 at 20:11

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell T8600D - Chronotherm IV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell T8600D - Chronotherm IV in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info