585058
5
Zoom out
Zoom in
Previous page
1/28
Next page
T8600D, T8601D AND T8602D CHRONOTHERM
®
IV DELUXE PROGRAMMABLE THERMOSTATS
68-0164—1
5
WIRES
THROUGH WALL
WALL
MOUNTING
HOLES
M15044
MOUNTING
SCREWS
WALL
ANCHORS
(2)
Fig. 3. Mounting the wallplate.
IMPORTANT
Use 18 gauge, color-coded thermostat cable for
proper wiring.
2. Securely tighten each terminal screw.
3. Push excess wire back into the hole.
4. Plug the hole with nonflammable insulation to prevent
drafts from affecting the thermostat.
Standard
Terminal
Designations
Alternate
Terminal
Designations Typical Connection Function Terminal Type
B— Heating damper or changeover valve Output 24V powered contact
CB
a
, C, X1, X2 Common Input
GF Fan relay Output 24V powered contact
OR Cooling damper or changeover valve Output 24V powered contact
OT, OT Outdoor temperature sensor (C7089B) Input
RV 24V system or heating transformer Input
RC 24V cooling transformer Input
W H1, R3 Heating relay Output 24V powered contact
Y C1, M Compressor contactor Output 24V powered contact
a
Some OEM models label the terminal for transformer common B.
M4826
FOR WRAPAROUND
INSERTION STRIP
7/16 IN. (11 MM).
FOR STRAIGHT
INSERTION STRIP
5/16 IN. (8 MM).
Fig. 4. Proper wiring technique.
Mounting Thermostat Wallplate
The thermostat mounts on the wallplate after they are
installed.
1. Engage tabs at the top of thermostat and wallplate. See
Fig. 5.
2. Press lower edge of case to latch.
NOTE: To remove the thermostat from the wall, first pull out
at the bottom of the thermostat; then remove the top.
Table 4. Terminal Designations and Descriptions.
5


Need help? Post your question in this forum.

Forumrules
1

Forum

honeywell-t8600d---chronotherm-iv

Reset search

  • The AC is not working. The repair person via a phone call said to turn off the system. How do I do this?
    I read the Manuel.
    The fuse is fine.
    Submitted on 28-7-2022 at 20:15

    Reply Report abuse
  • An HVAC repair person cannot come until next week. The AC is not working.
    He suggested I turn off the system. How do I do this? I read the manuel.
    It is not a problem with the fuse. Submitted on 28-7-2022 at 20:11

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell T8600D - Chronotherm IV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell T8600D - Chronotherm IV in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info