613686
16
Zoom out
Zoom in
Previous page
1/26
Next page
16
To Enter Installer Mode:
a. Ensure the slider is in the RUN position, then press and hold
and buttons
together for 8 seconds. Ignore the ‘NOT VALID’ message that is displayed for a
few seconds. The message ‘SET UP MENU’ will show briefly, followed by ‘SET
INSTALLER OK ?’
b. Press the
button to take you into the Installer Mode Parameter Menu.
c. Parameter 1 is now available to change. This is to allow you to change the
clock format from 12 hour AM/PM to 24 hour. At every step, the LoT™ Display
will inform you what the parameter means and what option you have selected.
The parameter number is shown on the display separated by a colon from the
parameter value.
d. You can change the parameter value by pressing the
or buttons. At this
point the description in the LoT™ Display will change and the parameter value
will flash. If you press the value will stop flashing and be saved for use.
INSTALLER
PARAMETER
Parameter
Number
Default
Value
Options Description
* Optimum start
9 0 0, 1, 2 0 = no optimum start
1 = delayed start
2 = optimum start on
* Optimum start limit 10 1 1, 2, 3 1 = 1 hour
2 = 2 hours
3 = 3 hours
* Optimum stop
11 0 0, 1 0 = disabled
1 = enabled
* Frost protection
temperature
12 5 5 to
16°C
Frost protection
temperature
* Minimum ON/OFF
time
13 1 1, 2,
3, 4, 5
mins
Minimum ON/OFF time
in minutes
* Cycle rate
14 6 3, 6, 9,
12
Number of boiler cycles
per hour
* Proportional band
width
15 1.5 1.5 to
3.0°C
Width of control
proportional band in °C
Failsafe mode (loss of
RF communications)
16 0 0, 1
0 = off
1 = heating on 20%
Reset all parameters
20 1 0, 1 0 = do not reset
1 = default parameters
FINE TUNING YOUR ST9120C
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell ST9120C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell ST9120C in the language / languages: English as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info