680980
13
Zoom out
Zoom in
Previous page
1/16
Next page
10. Unclip the mounting plate.
Press the top of the
thermostat downwards, pull
it loose and tilt forwards.
9. First remove the dial.
12. Remove the protective tab
between the batteries.
11. Mount directly to the wall.
The plugs and mounting
screws required are supplied.
Plugs
Screws
14. Replace the dial.
13. Attach the thermostat to
the mounting plate.
Step 1
Hook in here
Step 2
Click into place
Binding to the Boiler Relay
The Single Zone Thermostat is supplied ready to install,
binding is only required if the Thermostat and Boiler Relay
are purchased separately.
2. You can now bind the Single
Zone Thermostat. Touch and
hold on the left touch zone for
approximately 10 seconds.
3. The screen for binding the
Boiler Relay is now displayed.
Successful binding Failed binding
1. First, set the Boiler Relay
into binding mode by holding
down the BIND button for
5 seconds, until the red
LED ashes 0.5 seconds
on 0.5 seconds off.
Press here
4. When the symbol ‘bo’ is flashing, briefly touch
the left touch zone to send the binding signal,
at which point the
symbol will flash several times.
5. If binding has been successful the number indicates
the signal strength (1 = min to 5 = max).
If binding fails,
appears on screen. Please try again.
6. The red LED on the Boiler Relay will turn off when binding
has been successful.
Note: binding can be cancelled from the binding
screen by touching and holding on the left touch
zone for approximately 10 seconds.
Installation Menu
The single Zone Thermostat has an Installation
Menu that is used to set the minimum and maximum
temperature limits and the off temperature setting.
Maximum and minimum temperatures:
The maximum temperature you can set your
thermostat to is 3C and the minimum is 5ºC.
The off temperature:
If the thermostat is operated remotely, this is the temperature
value that is used when it is switched off from the remote app.
4. Touch the left touch zone to
display the off temperature
setting. Change this using
the setting ring as before.
5. The Installation Menu closes
automatically 10 seconds
after the last action.
2. The maximum temperature
limit is now displayed. The
setting can be changed using
the setting ring. There is no
need to confirm the value.
Touch zones.
There are two touch zones just below the thermostat
display, which are used to access menus and functions.
3. While this setting is flashing,
touch the left touch zone
briefly to display the minimum
temperature limit. This can also
be changed using the setting ring.
1. Rotate the setting ring fully to
the left until the minimum value
is shown. When the value starts
flashing, touch and hold on both
left and right touch zones for
approximately 10 seconds.
Activate the Installation Menu as follows:
10s
10s 10s
13


Need help? Post your question in this forum.

Forumrules
1

Forum

honeywell-single-zone---y87rf

Reset search

  • Any suggestions of why my thermostat keeps losing its binding to the boiler?
    Submitted on 28-11-2021 at 22:40

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Single Zone - Y87RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Single Zone - Y87RF in the language / languages: English as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell Single Zone - Y87RF

Honeywell Single Zone - Y87RF Additional guide - English - 8 pages

Honeywell Single Zone - Y87RF Additional guide - English - 3 pages

Honeywell Single Zone - Y87RF User Manual - English - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info