32489
3
Zoom out
Zoom in
Previous page
1/8
Next page
RTH2520 69-1867EF-1 13/6/06 3/4
3.2 Fan Operating Mode
Use the selector switch to set the fan to automatic
mode (AUTO) or continuous mode (ON).
Note: This switch is not used in a 2-wire installation
as the fan is not connected to the thermostat in this
type of installation.
3.3 Displaying the Temperature
The actual temperature is normally displayed. To view the setpoint,
press once on one of the buttons. The setpoint is displayed for
5 seconds along with the icon.
Note: Pressing either of the buttons more than once will
change the setpoint.
3.4 Setting the Temperature
Press one of the buttons until the desired temperature is dis-
played.
3.5 Backlight
The display illuminates for 12 seconds when the backlight button or
either of the buttons is pressed.
3.6 Thermostat Control Mode
3.6.1 Manual/Permanent Hold Mode
Maintains the temperature at a fixed setpoint. To place the thermo-
stat in this mode, press [ Mode ]. The house icon will disappear.
3.6.2 Programmable Mode
Maintains the temperature according to the energy-saving sched-
ule. To place the thermostat in this mode, press [ Mode ]. The cur-
rent period will be displayed. The four possible periods are:
To see the default program settings, see section 5.3.
Temporary Bypass
If you modify the setpoint (using the buttons) when the thermo-
stat is in Programmable mode, the thermostat will use the new set-
point for the next 2 hours. The house icon flashes during the
bypass. Afterwards the thermostat will return to the temperature set-
ting of the period currently underway.
3.7 Filter Replacement Indicator
After 500 hours of operation, an icon appears to indi-
cate that the filter needs replacement. Once the filter
is replaced, press [Filter] for 3 seconds to remove
the icon and reset the counter.
3.8 Battery Replacement Indicator
Install fresh batteries immediately when the icon starts
flashing. The icon flashes for 120 days before the bat-
teries are depleted. You should replace batteries once
a year or before leaving home for more than a month
even if the icon has not appeared.
After replacing the batteries, set the time, day and date (see sec-
tions 5.1 and 5.2). However, the temperature and program settings
are saved and do not need to be re-entered.
Warning: Before removing the batteries, place the
system switch on the thermostat to Off. Otherwise, the
heating/cooling unit might still be running even after
the batteries are removed.
n To access the configuration menu, press the backlight button
for 3 seconds.
o To go to the next parameter (menu item), briefly press the back-
light button.
p To modify a parameter, press .
q Repeat steps 2 and 3 if necessary.
r Press the backlight button for 3 seconds to exit the configura-
tion menu.
5.1 Setting the Time and Day
n Press [ Clk ]. The hour flashes.
o Set the hour using .
p Press [ Clk ]. The minutes flash.
q Set the minutes using .
r Press [ Clk ]. The day flashes.
s Set the day using . (MO: Monday, TU: Tuesday,
WE: Wednesday, TH: Thursday, FR: Friday, SA: Saturday and
SU: Sunday).
t Press [ Exit ] to exit.
5.2 Setting the Date
The date is needed for automatic daylight savings changeover.
n Press [ Clk ] for 3 seconds to display the year.
AUTO
The fan operates only when the heating or cooling sys-
tem is On (typical setting).
ON
The fan operates continuously. Use this setting to
improve air circulation and air cleaning.
Wake up Leave for work Return home Sleep
4. Configuration Menu
DISPLAY DESCRIPTION DEFAULT OPTIONS
Temperature display °F °C or °F
Time display 12 h 12 h or 24 h
Early start
1
Off On or Off
Automatic daylight savings
changeover
2
Off On or Off
Heating cycles per hour
3
4
2, 3, 4, 5 or 6
4
Cooling cycles per hour
3
4
2, 3, 4, 5 or 6
5
1
When Early Start is On, the thermostat determines when to start heating or cooling
so that the desired temperature is reached at the set time.
2
When this function is On, the thermostat automatically switches to daylight savings
time on the second Sunday of March and to normal time on the first Sunday of
November (see section 5.2).
3
Use the Heat/Cool selector switch to switch between the heating parameter and the
cooling parameter.
4
For optimal heating control, use the setting that matches your system as follows:
2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace), 4=15
min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).
5
The corresponding cooling cycle lengths are: 2=30 min., 3=20 min., 4=15 min.,
5=12 min., 6=10 min.
5. Programming
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell RTH2520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell RTH2520 in the language / languages: English, French as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell RTH2520

Honeywell RTH2520 User Manual - Spanish - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info