32483
3
Zoom out
Zoom in
Previous page
1/8
Next page
RTH1120 69-1875EF 22/2/06 3/4
3.1 System Operating Mode
Use the selector switch to place the system in Heating
mode (HEAT) or Cooling mode (COOL), or to turn the
system off.
Note: When you place the thermostat in Cooling mode, you might
need to wait up to five minutes before cooling can start. This is a
safety feature for the compressor. will flash on the screen until
cooling can start again.
3.2 Fan Operating Mode
Use the selector switch to set the fan to automatic
mode (AUTO) or continuous mode (ON).
Note: This switch is not used if you have a 2-wire
installation as the fan is not connected to the thermo-
stat.
3.3 Displaying the Temperature
The actual temperature is normally displayed. To view the setpoint,
press once on either of the buttons. The setpoint is displayed
for 5 seconds along with the icon.
Note: Pressing any of the buttons more than once will change
the setpoint.
3.4 Setting the Temperature
Press one of the buttons until the desired temperature is dis-
played.
3.5 Backlight
The display illuminates for 12 seconds when the backlight button or
either of the buttons is pressed.
3.6 Battery Replacement Indicator
An icon appears when the batteries need replacement.
This icon will flash for 120 days, then the thermostat
will cut power to the heating/cooling unit. The icon dis-
appears once the batteries are replaced. The tempera-
ture settings are saved and do not need to be re-entered.
Warning: Before removing the batteries, place the
system switch on the thermostat to Off. Otherwise, the
heating/cooling unit might still be running even after
the batteries are removed.
n To access the configuration menu, press the backlight button
for 3 seconds.
o To go to the next parameter (menu item), briefly press the back-
light button.
p To modify a parameter, press .
q Repeat steps 2 and 3 if necessary.
r Press the backlight button for 3 seconds to exit the configura-
tion menu.
Power supply: 2 AA batteries
Maximum load: 1 A @ 24 Vac per output
Setpoint range (heating): 41 to 82°F (5 to 28°C)
Setpoint range (cooling): 59 to 95°F (15 to 35°C)
Display range: 23 to 122°F (-5 to 50°C)
Storage temperature: -2 to 122°F (-20 to 50°C)
Temperature display resolution: 1°F (0.5°C)
Accuracy: ± 1°F (0.5°C)
Heating/cooling cycle lengths: 10, 12, 15, 20 or 30 minutes (pro-
grammable)
Compressor short-cycle protection (minimum off time): 5 minutes
Data memory: non-volatile
Dimensions: 5 in. x 3 in. x 1 in. (127 mm x 75 mm x 28 mm)
3. Basic Functions
AUTO
The fan operates only when the heating or cooling sys-
tem is On (typical setting).
ON
The fan operates continuously. Use this setting to
improve air circulation and air cleaning.
4. Configuration Menu
DISPLAY DESCRIPTION DEFAULT SETTINGS
Temperature
display
°F °C or °F
Heating cycles
per hour
1
4
2, 3, 4, 5 or 6
2
Cooling cycles
per hour
1
4
2, 3, 4, 5 or 6
3
1
When either the heating or cooling parameter is displayed, use
the system mode selector switch to alternate between the two
parameters.
2
For optimal heating control, use the setting that matches your
system as follows: 2=30 min (steam or gravity), 3=20 min (hot
water or 90%+ high-efficiency furnace),
4=15 min (gas or oil), 5=12 min (alternate setting for gas or oil),
6=10 min (electric).
3
The corresponding cooling cycle lengths are as follows: 2=30
min, 3=20 min, 4=15 min, 5=12 min, 6=10 min.
5. Technical Specifications
Printed in China
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell RTH1120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell RTH1120 in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info