Manual Honeywell R200C-N1 (page 9 of 80) (English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish)

795102

Zoom out

Zoom in

1/80

-9-

The initial interconnected CO alarm will beep continuously with the red “ALARM” text indicator flashing.

Other interconnected CO alarms will receive the signal after few seconds, and they will beep continuously

with the red “ALARM” flashing.

Reset Connection

a) Press 4 times the test/silence button and the yellow LED will light up.

b) While the yellow light is on, press and hold the test/silence button again.

c) When you hear a chirp and the yellow LED turns off, the connection has been reset successfully.

Connection fault

If the interconnected CO alarm connection fails, the green light will flash 3 times once every minute.

However, the CO alarm will still be able to effectively detect the carbon monoxide.

How to silence interconnected alarms

When an interconnected CO alarm has been activated, find the originating interconnected CO alarm,

which will be the one both emitting the audio signal and displaying the “ALARM” message. Mute this

originating alarm by pressing its test/silence button, and within 2 minutes the remaining interconnected

CO alarms will go back to standby.

Note: if you press the test/silence button on one of the interconnected CO alarms other than the

originating alarm, it will NOT be silenced, the remaining interconnected alarms will continue emitting

sound until the primary alarm is stopped.

12. Maintenance

The interconnected CO alarm does not require any maintenance other than to clean the outside case

occasionally with a clean tissue. Ensure that the holes on the front of the interconnected CO alarm are

not blocked with dust or dirt. We recommend to manually test the interconnected CO alarm once a

month by pressing and holding the TEST/SILENE button. Due to the loudness of the alarm, make sure that

you always stand at arm’s length distance from the unit when testing. If problems are found, the

interconnected CO alarm switches to the error mode (either siren error or sensor error). Dust is a major

cause of false alarms. Therefore, clean the interconnected CO alarm once a month. Use a vacuum cleaner

to gently remove any accumulated dust along the sides of the interconnected CO alarm. Never use a wet

cloth or detergent to clean your interconnected CO alarm, as this can be harmful to the sensor.

13. Warnings

This manual contains important safety information about the installation and operation of the

interconnected CO alarm. Read the manual carefully and keep it in a safe place for future reference. The

interconnected CO alarm should be installed by a competent person. Intended for either fixed or portable

installation, with portable apparatus almost certainly powered from internal batteries alone. Besides the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell R200C-N1 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 2.72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell R200C-N1 Manual

Product: