660644
35
Zoom out
Zoom in
Previous page
1/156
Next page
Configuration
Document 900.0856 Rev B 35
02/08
Note Some buttons on the infrared remote control may not be
supported, depending on the DVR model.
Table 3-1 Front Panel Buttons and Controls
Control Description
Camera Buttons
(1 to 16)
Pressing the individual camera buttons will cause the selected camera to
display full screen. Buttons 1 to 9 are also used to enter passwords.
DISPLAY Button The DISPLAY button has two functions. First, it toggles between different
display formats. The available formats are: 4x4, 3x3, 2x2 and PIP. Second,
pressing and holding the button for 5 seconds or longer will switch the video
output between Video Out (BNC or SVHS Out) and VGA Out.
SEQUENCE
Button
When in the live mode, pressing the SEQUENCE button displays live channels
sequentially.
FREEZE Button Pressing the FREEZE button freezes the current live screen.
SPOT Button Pressing the SPOT button allows you to select which cameras will display on
the four Spot monitors. After selecting the monitor you can opt to have that Spot
monitor display a single camera or all cameras sequentially. The infrared
remote control allows you to go directly to the individual Spot monitor menus.
MENU Button Pressing the MENU button enters the Setup screen. You will need to enter the
authorized user name and password to access Setup. Pressing the button also
closes the current menu or setup dialog box. In Playback mode, pressing
MENU displays the Search menu. In Search mode clip-copying can be done
instantly by pressing and holding the button for two or more seconds.
ALARM Button The ALARM button has two functions. First, it will reset the DVR’s outputs
including the internal buzzer during an alarm. Second, it will display the event
log when you are in the live monitoring mode unless there is an active alarm.
This operation can be user password protected.
ZOOM Button Pressing the ZOOM button zooms the current image on the screen. A PIP with
a rectangle temporarily displays showing what area of the screen has been
enlarged. You can use the arrow buttons to move the rectangle to another area.
Pressing (Enter) toggles the zoom size between 2x, 3x and 4x.
PTZ Button Pressing the PTZ button enters the PTZ (Pan/Tilt/Zoom) mode which allows you
to control properly configured cameras.
Up, Down, Left,
Right Arrow
Buttons
These buttons are used to navigate through menus and GUI. You can also use
them to change numbers by highlighting a number in the menu and using the
Up and Down arrow buttons to increase or decrease the number’s value.
The arrow buttons are also used to control Pan and Tilt when in the PTZ mode.
When in the PIP display format, pressing the Up and Down arrow buttons
moves the position of the small screen counter-clockwise and clockwise, and
pressing the Left and Right buttons moves through screen pages.
PANIC Button Pressing the PANIC button starts panic recording of all camera channels, and
displays on the screen. Pressing the button again will stop panic recording.
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HRXD16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HRXD16 in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info