660637
89
Zoom out
Zoom in
Previous page
1/108
Next page
Document 800-21261V3 Rev A 05/2016
Remote User Guide
Performance Series Full PoE
Network Video Recorder
HEN04112 HEN08112 HEN16122
HEN04122 HEN08122 HEN16142
HEN04102 HEN08142 HEN16162
HEN08102 HEN16102
Remote
User Guide
Revisions
Issue Date Revisions
A 08/2015 New document. (Based on 800-20017)
V1 Rev A 10/2015 Added a note in the Configurations section, table 3-2.
V2 Rev A 03/2016 Amended the list of NVR models.
V3 Rev A 05/2016 Removed any reference to Google Chrome.
Contents | 5
800-21261V3 - A - 05/2016
Contents 1
About This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Overview of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1 Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Preparing to Use the Device Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Before You Log In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
LAN Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Section 1: Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Section 2: Monitor Channels and Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Monitor Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Start Talk Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Instant Record Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Local Play Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Section 3: PTZ Control Panel, Image and Alarm Configuration Panels . . . . . . . . . . . . . . . . 22
PTZ Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Image and Alarm Configuration Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Section 4: Viewer Configuration Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
WAN Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
The Difference Between LAN and WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Logging Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Uninstalling the Web Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2 Live Viewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Live Viewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Image/Relay-out Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuring Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connection Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Online User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Configuring the Camera Setup through the Remote Interface . . . . . . . . . . . . . . . . . . 33
Configuring Camera Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Configuring Encoding Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Configuring the Channel Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Configuring the Network Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Configuring TCP/IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Configuring the Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Configuring WIFI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Configuring 3G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
www.honeywell.com/security
6 | Performance Series Full Poe Embedded NVR Remote User Guide
Configuring PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configuring DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Quick DDNS and Client-end Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Configuring the IP Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Configuring Email. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Configuring FTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Configuring UPnP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Configuring SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Auto-Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Alarm Centre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
HTTPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Configuring Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Configuring Event Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Configuring Video Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Configuring Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Configuring Alarm Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Configuring for Abnormalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Configuring Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Configuring Storage Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Configuring Local Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Configuring Manual Recording Storage Settings . . . . . . . . . . . . . . . . . . . . . . . . . 76
Configuring General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Configuring Display Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Configuring PTZ Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Automatic Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Import/Export . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Default. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
4 Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Downloading Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Loading More . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
5 Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Activating Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figures | 7
800-21261V3 - A - 05/2016
Figures 1
Figure 1-1 IE Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 1-2 Controls Installation Popup Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 1-3 Unblocking Security Plug-ins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 1-4 Web Service Login Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 1-5 LAN Mode Main Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 1-6 LAN Main Window Function Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 1-7 Monitor Channels Section and Function Buttons . . . . . . . . . . . . . . . . . . . . . . . . .20
Figure 1-8 Main Stream and Extra Stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 1-9 Start Talk Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 1-10 Talk Mode Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 1-11 Instant Record Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 1-12 Local Play - Select a File Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 1-13 WAN Mode Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 1-14 Login Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 2-1 Live View Video Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 2-2 Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 2-3 Version Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 2-4 Log Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 2-5 Connection Log Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 2-6 Online User Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 3-1 Camera Conditions Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 3-2 Encoding Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 3-3 Snapshot Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 3-4 Video Overlay Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 3-5 Save Path Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 3-6 Channel Name Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 3-7 TCP/IP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 3-8 Connection Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Figure 3-9 Wifi Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Figure 3-10 CDMA/GPRS Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Figure 3-11 Mobile Setup Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Figure 3-12 PPPoE Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 3-13 DDNS Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Figure 3-14 IP Filter Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Figure 3-15 Email Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
www.honeywell.com/security
8 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-16 FTP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Figure 3-17 UPnP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Figure 3-18 SNMP Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Figure 3-19 Multicast Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Figure 3-20 Auto Register Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 3-21 Alarm Centre Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Figure 3-22 HTTPS Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Figure 3-23 Create Server Certificate Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 3-24 Server Certificate Confirmation Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 3-25 File Download Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Figure 3-26 Certificate Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 3-27 Certificate Import Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Figure 3-28 Certificate Import Wizard - Certificate Store Window . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 3-29 Certificate Import Wizard - Completion Message . . . . . . . . . . . . . . . . . . . . . . . . . 60
Figure 3-30 Security Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 3-31 Certificate Import - Confirmation Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 3-32 Connection Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Figure 3-33 Switch Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Figure 3-34 Motion Detect Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Figure 3-35 Video Loss Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 3-36 Camera Tampering Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Figure 3-37 WEB - Alarm Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Figure 3-38 WEB - Net Alarm Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 3-39 WEB - Alarm Output Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 3-40 WEB - Abnormality Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Figure 3-41 Configuring for Abnormalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Figure 3-42 Schedule Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Figure 3-43 Set Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Figure 3-44 Local Storage Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Figure 3-45 Manual Recording Storage Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Figure 3-46 General Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Figure 3-47 Date & Time Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 3-48 Holiday Settings Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 3-49 Display Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Figure 3-50 Tour Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Figure 3-51 WEB - RS232 Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 3-52 PAN/TILT/ZOOM Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Figure 3-53 User Name Account Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Figure 3-54 Add User Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 3-55 Modify User Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Figure 3-56 Group Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 86
Fig
ure 3-57 Add Group Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Figure 3-58 Modify Group Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 3-59 Auto Maintain Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Figure 3-60 Import/Export Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figures | 9
800-21261V3 - A - 05/2016
Figure 3-61 Default Settings Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Figure 3-62 Upgrade Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Figure 4-1 Playback Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 4-2 List of Recorded Video Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Figure 4-3 Playing Back Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Figure 4-4 Downloading Recorded Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Figure 4-5 Download by File/Download by Time Interfaces . . . . . . . . . . . . . . . . . . . . . . . . .95
Figure 5-1 Alarm Configuration Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
www.honeywell.com/security
10 | Performance Series Full Poe Embedded NVR Remote User Guide
Tables | 11
800-21261V3 - A - 05/2016
Tables 1
Table 1-1 PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 1-2 Viewer Configuration Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Table 2-1 Live View Video Window Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 2-2 Live View Video Window Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 2-3 Image Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 2-4 Log Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 3-1 Camera Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 3-2 Encoding Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 3-3 Snapshot Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 3-4 Video Overlay Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Table 3-5 TCP/IP Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 3-6 Network Connection Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Table 3-7 CDMA/GPRS Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 3-8 DDNS Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Table 3-9 DDNS Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Table 3-10 Email Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Table 3-11 FTP Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Table 3-12 SNMP Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 3-13 Switch Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Table 3-14 WEB - Motion Detection Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 3-15 WEB - Alarm Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Table 3-16 Configuring for Abnormalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 3-17 Scheduled Storage Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 3-18 Schedule Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Table 3-19 Recording Storage Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Table 3-20 General Settings Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Table 3-21 Date & Time Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 3-22 GUI Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Table 3-23 Display Tour Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Table 3-24 RS232 Web Configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Table 3-25 PAN/TILT/ZOOM Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Table 3-26 Import/Export Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 5-1 Alarm Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
www.honeywell.com/security
12 | Performance Series Full Poe Embedded NVR Remote User Guide
800-21261V3 - A - 05/2016
About This Document
This document describes how to access Honeywell’s Performance Series Full PoE Network
Video Recorder remotely using a browser-based web client.
This document is intended primarily for remote users.
Overview of Contents
This document contains the following chapters:
Chapter 1, Logging In
Chapter 2, Live Viewing
Chapter 3, Configuration
Chapter 4, Playback
Chapter 5, Alarms
www.honeywell.com/security
14 | Performance Series Full Poe Embedded NVR Remote User Guide
Related Documents
For more information about using the Performance Series Full PoE Network Video Recorder,
refer to the following documents:
* These part numbers are subject to change. Please consult the Performance Series Full PoE
Network Video Recorder product webpage for the latest versions of these documents.
Document title Part number*
Performance Series IP Network Video Recorder User Guide 800-21090
Performance Series IP NVR Quick Connection Guide 800-21088
Performance Series IP NVR Quick Network Guide 800-21089
800-21261V3 - A - 05/2016
1
Logging In 1
This chapter includes:
PC requirements for the web client software
Logging in to the web client software
The web client software’s main page
Preparing to Use the Device Web Client
PC Requirements
Before You Log In
Ensure that the following conditions are met:
Ensure that the network connection is good.
Ensure that the NVR and PC network setup is correct. See the network setup: Main
Menu
SettingNetwork.
Ping to ensure that the network connection is good. Ping *** *** *** *** (where *** ***
*** *** is the NVR’s IP address). The return TTL should be less than 225.
Table 1-1 PC Requirements
Component Minimum Requirement
Processor Quad core
System memory (RAM) 2G or higher
Non-integrated video card 256M or higher
www.honeywell.com/security
16 | Performance Series Full Poe Embedded NVR Remote User Guide
Note Before you uninstall the web control, close all web pages. If you do not, then the
uninstallation procedure might result in an error.
The current NVR supports various browsers such as Apple Safari and Mozilla Firefox. The
NVR supports multiple-channel monitoring (depending on your model) on an Apple PC.
Logging In
1. Open a Web browser window.
Note These instructions were created using IE. You can use Internet Explorer (IE),
Safari, or FireFox.
Figure 1-1 IE Window
2. Enter the NVR IP address in the address field.
Enter the IP address
Logging In | 17
800-21261V3 - A - 05/2016
For example, if your NVR’s IP address is 192.168.1.108, then enter http://192.168.1.108
in the address field.
A message pops up asking if you want to install controls.
Figure 1-2 Controls Installation Popup Message
3. Click Install to install the controls.
Note The relevant plug-ins might be blocked by your web browser security settings.
See Figure 1-3.
Figure 1-3 Unblocking Security Plug-ins
When installation is successful, the Web Service login window appears.
www.honeywell.com/security
18 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 1-4 Web Service Login Window
4. Enter your username (default: admin) and password (default: admin), then click Login.
Note For security, we recommend that you modify your password on your first log in.
LAN Mode
The LAN main window is divided into 4 main sections. See Figure 1-5. In LAN mode, you can
select different channels and different modes at the bottom of the interface.
Logging In | 19
800-21261V3 - A - 05/2016
Figure 1-5 LAN Mode Main Window
Section 1: Function Buttons
Figure 1-6 LAN Main Window Function Tabs
There are six function tabs:
Preview: You are currently in the Preview (Live) mode, where you can see all these tabs.
Playback: See Local Play Button on page 22
Alarm: See Alarms on page 95
Setup: See Configuration on page 33
Info: See Information on page 30
Logout: See Logging Out on page 25
4
2
3
1
www.honeywell.com/security
20 | Performance Series Full Poe Embedded NVR Remote User Guide
Section 2: Monitor Channels and Function Buttons
Figure 1-7 Monitor Channels Section and Function Buttons
Monitor Channels
The Monitor Channels section displays monitor channels that are successfully connected to
the NVR. Left-click to select a channel for viewing, or click Start All.
Note The Start All button changes to Open All on the GUI.
Main Stream and Extra Stream - Navigate your mouse to a camera channel window to find the
Main Stream and the Extra Stream.
The Start All button enables/disables all channels in the real-time monitor. You can also select
the Main Stream or the Extra Stream.
Logging In | 21
800-21261V3 - A - 05/2016
Figure 1-8 Main Stream and Extra Stream
Start Talk Button
Figure 1-9 Start Talk Button
Enabling Bi-Directional Communication
1. Click to enable bi-directional communication.
2. Click in the control panel on the right to select the bi-directional communication mode.
There are four options for the communication mode: DEFAULT, G711a, G711u, and
PCM.
Figure 1-10 Talk Mode Options
Note After you enable bi-directional communication, if the audio input port that goes
from the device to the client end is using the first channel audio input port, then
the system will not encode the audio data from that one channel. Refer to the
Setting Up Bi-Directional Communication Connection section in the User Guide
for more about the audio connections.
Disabling Bi-Directional Communication
After turning on Bi-directional Communication, the Start Talk button turns into an End Talk
button. Click this button to end bi-directional communication.
www.honeywell.com/security
22 | Performance Series Full Poe Embedded NVR Remote User Guide
Instant Record Button
Figure 1-11 Instant Record Button
Click Instant Record, and the button turns blue. The NVR begins manual recording. Click
Instant Record again to restore the NVR to the previous recording mode.
Local Play Button
The NVR can play back saved files (in the.dav format) in the PC.
1. Click Local Play, and an interface appears for selecting the playback file.
Figure 1-12 Local Play - Select a File Interface
2. Select a file, then click Open. A media player opens and plays the selected video.
Section 3: PTZ Control Panel, Image and Alarm Configuration Panels
PTZ Control Panel
Refer to the User Guide for more about controlling PTZ cameras.
Image and Alarm Configuration Panels
Refer to the User Guide or see Configuring Image Settings on page 29 for more information
about Image settings.
Refer to the User Guide or see Alarms on page 95 for more information about Alarms.
Logging In | 23
800-21261V3 - A - 05/2016
Section 4: Viewer Configuration Controls
WAN Login
After you have successfully logged in, you will be in WAN mode. In WAN mode, you can select
different channels and different modes at the bottom of the interface.
Table 1-2 Viewer Configuration Controls
Button Name Description
Video Quality Click to select the video quality. Select either
High quality or Low quality.
Fluency Click to configure the fluency. Select from
Fluency Level 1, Fluency Level 2, Fluency
Level 3, Middle level, Latency Level 1,
Latency Level 2, and Latency Level 3.
Full Screen Click to switch the viewer to show video full
screen. Click Esc (on your PC) to quit full
screen.
Vertical Synchronization Click to configure vertical synchronization.
Single-channel Window Click to switch to single channel viewing.
Four-channel Window Click to switch to switch to four channel
viewing.
www.honeywell.com/security
24 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 1-13 WAN Mode Interface
The Difference Between LAN and WAN
In WAN mode, by default, the NVR system opens the main stream for the first channel and
displays it on the monitor. The Open/Close button in the left pane does not work.
Note The window display mode and the channel number are assigned by default. For
example, for the 16-channel NVR, the maximum window split is 16 screens.
When in Multiple-channel monitor mode, the NVR system assigns an extra stream to
monitor, by default. Double-click a channel, and the NVR system switches to a single
channel in the monitor. There are two icons in the top left corner of the channel. M means
Main Stream. S means Sub Stream.
If you log in through WAN mode and are using the video function, then the NVR system
does not support alarm activation in the Alarm Setup interface.
Note For the Multiple-channel monitoring mode, by default, the NVR system assigns
an extra stream for monitoring. For each channel, the NVR supports both a Main
stream and a Sub stream. For one-channel live viewing, the Main Stream is used;
for Multiple-channel viewing, the Sub Stream is used. In multiple-channel mode,
all channels try to synchronize the time setting to the network, but the ability to
synchronize depends on your network settings.
Logging In | 25
800-21261V3 - A - 05/2016
Note Because of bandwidth limitations, the NVR system can not support monitoring
and playback at the same time. To enhance search speed, the NVR system
automatically closes the monitoring or playback interface when you are
searching for recorded video in the configuration interface.
Logging Out
Click the Logout tab in the Main Menu. The NVR returns to the Login interface.
Figure 1-14 Login Interface
Uninstalling the Web Control
You can use the web un-install tool uninstall_web.bat to uninstall the web control plugin.
Note Before un-installing the web control plugin, close all web pages. If you do not,
then you might experience an error.
www.honeywell.com/security
26 | Performance Series Full Poe Embedded NVR Remote User Guide
800-21261V3 - A - 05/2016
2
Live Viewing 2
This chapter includes:
A description of the NVR web client.
Descriptions of image/relay output settings, including image settings.
Descriptions of the Information available for viewing in live view, including system version,
log, connection log, and online user information.
Live Viewing
Left-click a channel name in Section 2, the Monitors Channel section, to select that channel for
viewing.
The video window shows statistics about the video.
www.honeywell.com/security
28 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 2-1 Live View Video Window
Table 2-1 Live View Video Window Controls
Table 2-2 Live View Video Window Controls
Control Description
Display Device
Information
Shows the following information about the video:
IP address
Channel number
Bit rate
Stream: Select either M for Main stream or S for sub stream.
Digital Zoom Click this button and then left drag the mouse in the zone to zoom
in. Right-click the mouse to return to the original viewing status.
Local Record When you click the Local Record button, the system/NVR begins
recording.
The recorded file is saved to the default system folder:
\RecordDownload.
Snapshot Click to take a snapshot of the currently viewed video. All images
are saved to the default system folder: \picture download.
Stream
Channel Number SnapshotSnapshot Audio
IP Address Bit Rate
Digital Zoom
Local
Record
Close
Window
Live Viewing | 29
800-21261V3 - A - 05/2016
Image/Relay-out Settings
Configuring Image Settings
Here you can adjust the selected channel’s brightness, contrast, hue, and saturation.
Figure 2-2 Image Settings
1. Click to select one channel’s video. The currently selected channel border turns Green to
indicate it is selected.
2. Click the Image adjustment buttons in Section 8. See LAN Mode Main Window on page 19.
To return the NVR system to default settings, click Reset.
Audio Turn audio On or Off.
Note This control has nothing to do with the system audio setup.
Close Window Close video in the current window.
Table 2-2 Live View Video Window Controls
Control Description
Table 2-3 Image Settings
Setting Description
Adjusts the monitor’s video brightness.
Adjusts the monitor’s video contrast.
Adjusts the monitor’s video hue.
Adjusts the monitor’s video saturation.
Restores the system to its defaults value.
www.honeywell.com/security
30 | Performance Series Full Poe Embedded NVR Remote User Guide
Note All of these configurations apply to the Web Viewer only.
Information
Version
1. Click the arrow next to System to expand the System menu tree.
2. Click Version to open the Version configuration interface.
Figure 2-3 Version Configuration Interface
Here you can view the recording channel, the alarm input/output information, the software
version, and the release date. None of these values can be changed; they are viewable
only.
Log
Click Log in the System menu to open the Log configuration interface.
Live Viewing | 31
800-21261V3 - A - 05/2016
Figure 2-4 Log Configuration Interface
Connection Log
1. Click Search to open the Connection Log interface.
Table 2-4 Log Configurations
Configuration Description
Start Time Set a start time for the log.
End Time Set an end time for the log.
Type Select from System Operation, Configuration Operation,
Data Operation, Event Operation, Record Operation, User
Management, Log Clear, and All.
Search Click Search to find a log or logs that fit the search
requirements (Begin time, End time, and Type).
You can click Stop to terminate the current search.
Detailed Information Select one item to see its detailed information.
Clear Click to clear the found log files.
Note You can not clear by log file.
Backup Click to backup the currently selected files to the selected PC.
www.honeywell.com/security
32 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 2-5 Connection Log Interface
2. Set a Start and End Time, select a Channel.
3. Click Search to find the connection log.
Online User
Click Online User in the System menu to open the Online User interface.
Figure 2-6 Online User Configuration Interface
You can see what users are currently online.
800-21261V3 - A - 05/2016
3
Configuration 3
This chapter includes descriptions about how to configuring the following:
•Camera setup
•Network setup
Event settings
Storage
General settings, including the following:
the device’s name and number
the interface language
the video standard
what happens when the HDD is full
the pack duration
Setup
Configuring the Camera Setup through the Remote Interface
If the NVR connects to an IP camera through a private protocol, then the Camera Conditions
page displays. If the NVR connects to an IP camera through the ONVIF protocol, then the
Camera Conditions does not display.
Configuring Camera Image Settings
In the Camera Conditions window, you can view the camera device properties. Any changes
are immediately active after you set them.
Click Camera under REMOTE to open the Conditions interface.
www.honeywell.com/security
34 | Performance Series Full Poe Embedded NVR Remote User Guide
Note The NVR automatically defaults to selecting channel 1 when you navigate
between configuration interfaces. For example, if you have selected channel 3 on
the Video&Audio configuration interface, and then navigate to the Channel Name
configuration interface, the NVR defaults to channel 1 in the Channel selection
drop-down.
Figure 3-1 Camera Conditions Interface
Table 3-1 Camera Conditions
Setting Description
Channel Select a channel from the dropdown list.
Note The NVR shows only the number of connected
cameras.
Scene Select a pre-programmed scene selection for different kinds
of lighting conditions for various times of the day. Select from
Day, Night, Normal, or Switch by Period. If you select
Switch by Period, then you configure the times for sunrise
and sunset.
Saturation Adjusts monitor window saturation. Select from 0 to 100. The
default setting is 50. The recommended range is 40 to 60.
The higher the number, the stronger the color. This value has
no effect on the general brightness of the video. The video
color might become too strong if the value is too high.
Note If the value is too low, the video might be poor.
Mirror Enable or disable the mirror function.
Configuration | 35
800-21261V3 - A - 05/2016
Configuring Encoding Settings
Configuring the Encoding
Click VIDEO&AUDIO under Remote to open the Encoding interface.
Brightness Adjusts the monitor window brightness. The default setting is
50.
The higher the number, the brighter the video. When you
select a value, the bright and dark elements of the video are
adjusted. Use this function to adjust video brightness when
the entire picture is too dark or too bright. Select from 0 to 100.
The recommended range is 40 to 60.
Note The video might become washed out if you select a
high brightness value.
Contrast Adjusts monitor window contrast. Select from 0 to 100. The
default setting is 50. The recommended range is 40 to 60.
The higher the value, the higher the contrast between light
and dark elements in the image. Use when the video
brightness is good, but the contrast is not.
The video might become washed out if you select a low
contrast value. If the value is too high, the dark sections might
lose brightness and the light parts might become
overexposed.
Sharpness Affects the edge definition of objects in the image. The higher
the setting, the more image detail is apparent.
Note Noise in the image might become noticeable at higher
settings.
Period Divide a day (24-hour period) into two periods, then set
different sharpness, brightness, contrast, saturation, and gain
settings for each period.
3D NR Enable/disable 3D noise reduction.
Flip Select an angle on which the video will be flipped.
Light Adjust Backlight Compensation. Select either Low or High.
Scene Mode Select from several configured color modes such as Auto,
Sunny, Night, or Customized. Selecting a Scene Mode will
adjust the hue, brightness, and contrast of the video. If you
select Customized, then you select the hue, brightness, and
contrast of the video.
Day/Night Select from Colorful, Auto, or B/W.
Table 3-1 Camera Conditions
Setting Description
www.honeywell.com/security
36 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-2 Encoding Interface
Note If the NVR fails to retrieve the configuration information for your selected
camera/channel, then you should navigate to a different window (such as
Snapshot or Overlay), then navigate back to the Encode window.
Table 3-2 Encoding Configurations
Setting Description
Channel Select a channel from the dropdown list
Code Stream Type Select from Main Stream, Motion Stream, and Alarm
Stream. You can select different encoding frame rates for
different recorded events.
The NVR system supports active control frame function (ACF),
which allows you to record in different frame rates.
For example, you can use a high frame rate to record
important events, and configure a lower frame rate for
recording scheduled events. ACF allows you to set different
frame rates for motion detection recording and alarm
recording.
Video Enable Click to enable the extra video stream. Enabled by default.
Compression The main bit stream supports H.264. The extra stream
supports H.264 and MJPG.
Configuration | 37
800-21261V3 - A - 05/2016
Configuring Snapshot Settings
Figure 3-3 Snapshot Settings Interface
Resolution The NVR system supports various resolutions, which you can
select from a dropdown list.
Note The selection is different for each NVR series. The
Performance Series Full PoE Network Video
Recorders can automatically detect a connected 720p
or 1080p camera’s configured resolution (as 720p or
1080p) But you must manually configure the resolution
(960H or below) for analog cameras, and 1080p HQA
cameras that are in SD mode.
Frame Rate PAL: 1 to 25 fps
NTSC: 1 to 30 fps
Bit Rate Type Select either CBR (constant bit rate) or VBR (variable bit rate).
Note If your device is connected to the NVR through ONVIF,
then you can not select VBR. If your device is
connected to the NVR through a private protocol, then
you can select either CBR or VBR.
Bit Rate Main Stream: Select a bit rate to change the video quality.
The larger the bit rate, the better the video quality. We
recommend that you accept the default bit rate. The GUI also
displays the reference bit rate range and frame rate for the
selected resolution.
Extra Stream: In DBR, the bit rate is the maximum value. For
dynamic video, the NVR system will decrease the frame rate
or video quality to maintain the bit rate. The value is null for
VBR mode.
Enable Watermark Allows you to verify that the video has not been tampered.
Watermark String Enter the text for the watermark. The default watermark is
DigitalCCTV. The maximum text length is 85 characters. You
can use only letters, numbers, and an underline.
Table 3-2 Encoding Configurations
Setting Description
www.honeywell.com/security
38 | Performance Series Full Poe Embedded NVR Remote User Guide
Video Overlay
Figure 3-4 Video Overlay Configurations
Table 3-3 Snapshot Settings
Setting Description
Channel Select a channel.
Mode Select from two modes: Timing (scheduled) and Trigger.
Timing: the snapshot is available during the period you
specify.
Trigger: the snapshot is available only when a motion
detection alarm, tampering alarm, or local activation alarm
occurs.
Image Size Matches the resolution of the main stream.
Quality Select from six quality levels.
Snapshot Frequency Set the snapshot frequency. The value ranges from 1s to 7s,
or you can set a customized time. The maximum is
3600s/picture.
Configuration | 39
800-21261V3 - A - 05/2016
Configuring the Save Path
Configure the save path for snapped images (click in the preview interface) or recorded
video (click in the preview interface).
Figure 3-5 Save Path Configuration Interface
The default save path is C:\PictureDownload for snapshots and C:\RecordDownload for
recorded video.
Click Browse to change the save path, and then click Save.
Configuring the Channel Name
1. Click Channel Name under REMOTE to open the Channel Name configuration interface.
Table 3-4 Video Overlay Configurations
Setting Description
Cover-Area 1. Select Preview or Monitor.
2. Click Set, then draw a privacy mask on the specified video
in preview or on monitor video.
The NVR system supports a maximum of four privacy zones.
Channel Display Enable this function so that the system overlays channel
information in the video window.
Use the mouse to drag the channel display into position.
You can see the channel on the live WEB video or the
playback video.
Time Display Enable this function so that the system overlays time
information in the video window.
Use the mouse to drag the time display into position.
You can see the time on the live WEB video or the playback
video.
www.honeywell.com/security
40 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-6 Channel Name Configuration Interface
2. Enter a new channel name, then click Save.
Configuring the Network Setup
Configuring TCP/IP
Click TCP/IP under NETWORK to open the TCP/IP configuration interface.
Configuration | 41
800-21261V3 - A - 05/2016
Figure 3-7 TCP/IP Configuration Interface
Table 3-5 TCP/IP Configurations
Configuration Description
Mode There are two modes: STATIC and DHCP.
The IP address, submask, and gateway is inactive and
not configurable when you select the DHCP mode to
automatically search for the IP address.
•If you select STATIC mode, then you need to manually
configure the IP address, submask, and gateway.
•If you select DHCP mode, then you can only view the IP
address, submask, and gateway. You can not configure
these values.
If you switch from the DHCP mode to the static mode,
then you need to reset the IP parameters.
The IP address, submask, gateway, and DHCP are
read-only values when the PPPoE dial is OK.
MAC Address Displays the MAC address. This field is not configurable.
MTU Use the default MTU (maximum transmission unit) value.
IP Version Select the IP version, either IPv4 or IPv6.
You can use either version to access the camera’s IP address.
IP Address 1. Use your PC’s keyboard to enter the IP address.
2. Set the Subnet mask and Default gateway.
Subnet Mask If you selected the STATIC mode, then enter a Subnet Mask
value.
Default Gateway If you selected the STATIC mode, then enter a Default
Gateway value.
Preferred DNS Enter the DNS IP address.
www.honeywell.com/security
42 | Performance Series Full Poe Embedded NVR Remote User Guide
Configuring the Connection
Click Connection under NETWORK to open the Connection configuration interface.
Figure 3-8 Connection Configuration Interface
Alternate DNS Enter an alternate DNS IP address.
Note For the IPv6 version IP address, the Preferred DNS and Alternate DNS shall be no
more the 128 digits. They also can not be left blank.
LAN Download Enable this function so that the system can process the
downloaded data first. The download speed is 1.5X or 2.0X of
the normal speed.
Table 3-5 TCP/IP Configurations
Configuration Description
Table 3-6 Network Connection Configurations
Configuration Description
Max Connection The maximum Web connection for the same NVR. The value ranges
from 1 to 20. The default is 20.
TCP Port The default is 37777. You can enter the actual port number, if
necessary.
UDP Port The default is 37778. You can enter the actual port number, if
necessary.
HTTP Port The default is 80. You can enter the actual port number, if necessary.
RTSP Port The default is 554.
RTSP Format A non-configurable field that shows the RTSP format.
Configuration | 43
800-21261V3 - A - 05/2016
Configuring WIFI
Note This section applies only to devices with Wifi capability, such as tablet
computers, smartphones, and laptop computers.
1. Click Wifi under NETWORK to open the Wifi configuration interface.
Figure 3-9 Wifi Configuration Interface
2. Click to enable Wifi.
3. Double-click the name of a wireless device to connect to it.
Note Click Refresh to update the list of wireless network information.
Configuring 3G
Configuring CDMA/GPRS
1. Click 3G under NETWORK to open the 3G configuration interface.
2. Click the CDMA/GPRS tab to open the CDMA/GPRS configuration interface.
www.honeywell.com/security
44 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-10 CDMA/GPRS Configuration Interface
Table 3-7 CDMA/GPRS Configurations
Configuration Description
WLAN Type Select a 3G network type to distinguish this 3G module from
different ISPs. Choose from WCDMA, CDMA1x, for example.
APN & Dial No. APN and the Dial No. are important PPPoE parameters. The
APN (Access Point Name) and the Dial No. are automatically
received by the NVR after connecting to a 3G module.
Dial/SMS Activate Enable/disable Dial/SMS Activate. When enabled, if the user
sends an "ON" message by phone to the NVR, then the NVR
dials and connects with CDMA/GPRS. If the user sends an
"OFF" message by phone to the NVR, then the NVR breaks the
link with CDMA/GPRS.
AUTH Authorization. Choose from PAP, CHAP, or NO_AUTH.
Username / Password Enter a username and password for logging onto the 3G
network.
Pulse Interval Configure a time for ending the 3G connection after you close
the extra stream monitor. For example, if you select 60 here,
the NVR ends the 3G connection 60 seconds after you close
the extra stream monitor.
Configuration | 45
800-21261V3 - A - 05/2016
Configuring the Mobile Settings
Click Mobile Setup under 3G to open the Mobile Setup configuration interface.
Figure 3-11 Mobile Setup Configuration Interface
Activate/deactivate 3G connected phones or mobile phones, or the phone you configured to get
alarm messages.
Configuring PPPoE
1. Click PPPoE under NETWORK to open the PPPoE configuration interface.
Note If the Pulse Interval is 0, then the system does not end the 3G connection after you
close the extra stream monitor.
Note The Pulse Interval here is for the extra stream only. This field is inactive if you are
using a main stream monitor.
IP Address Non-configurable. After the NVR connects to the network
through CDMA/GPRS, it receives an IP address, which
displays here.
Wireless Signal When the NVR connects to 3G through GPRS/CDMA, by
clicking SEARCH, you can see the signal strength.
Table 3-7 CDMA/GPRS Configurations
Configuration Description
www.honeywell.com/security
46 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-12 PPPoE Configuration Interface
2. Enter the PPPoE User name and Password, which you receive from your Internet Service
Provider (ISP).
3. Enable the PPPoE function.
4. Click Save to save the changes.
5. Reboot the device to activate these changes.
After rebooting, the device should connect to the Internet through the PPPoE connection.
The IP address is found in the WAN from the IP address column.
Note You need to use the previous IP address in the LAN to log into the device. Go to
the IP address field, which is found in the device’s current device information.
You can access the NVR through this new address.
Configuring DDNS
Use DDNS to connect the various servers so that you can access the system through the server.
1. Go to the corresponding service website to apply for a domain name.
2. Access the system through that domain name.
Note This works even if your IP address has changed.
3. Select DDNS from the drop-down list.
Table 3-8 DDNS Configuration Options
Configuration Description
DDNS Type Select the DDNS protocol from the drop-down list, then
enable the DDNS function.
Server IP The DDNS server IP address.
Configuration | 47
800-21261V3 - A - 05/2016
Honeywell DDNS
The Honeywell DDNS function works with a special DDNS server and special Professional
Surveillance Software (PSS).
Click DDNS under NETWORK to open the DDNS configuration interface.
Figure 3-13 DDNS Configuration Interface
Operation
Before you can use Honeywell DDNS, you need to enable this service and configure the proper
server address, port value, and domain name.
Domain Mode The DDNS server port.
Domain Name Your self-defined domain name.
Email Address Server email address.
Table 3-8 DDNS Configuration Options
Configuration Description
Table 3-9 DDNS Configurations
Parameter Description
DDNS Type You can select the DDNS protocol from the drop-down list, and
then enable the DDNS function. Select the Honeywell DDNS
server (which is free) to enable the DDNS function.
Server IP This is the DDNS server IP address. Under Honeywell DDNS, the
default server address is www.hennvr-ddns.com.
Domain Mode Select Default Domain or Custom Domain Name. The default is
Default Domain. If you select Custom Domain Name, then you
must enter a domain name.
Domain Name The default domain name is MAC address.hennvr-ddns.com.
You can define the prefix.
www.honeywell.com/security
48 | Performance Series Full Poe Embedded NVR Remote User Guide
Note Do not register frequently. You need to wait at least 60 seconds between
registration requests. Too many registration requests might leave your server
vulnerable to attacks.
Note The system DDNS server might take back a domain name that is idle for one
year. If you configure your email address in the DDNS configuration, you will get
a notification email before the domain name is taken back.
Quick DDNS and Client-end Introduction
Background Introduction
If you use ADSL to log into the network, then the device IP is not fixed. The DDNS function allows
you to access the NVR via the registered domain name. Additional to the general DDNS, the
Quick DDNS works with the manufacturer’s device so that it can add the extension function.
Function Introduction
The quick DDNS client has the same function as other DDNS client ends. It bonds the domain
name and the IP address. Currently, the DDNS server only works with our own devices. You
must regularly refresh the bonding relationship between the domain and the IP. There is no
username, password, or ID registration on the server. However, each device has a default
domain name (generated by the MAC address). You can also use a customized valid domain
name which has not been registered.
Quick DDNS Operation
Before you use Quick DDNS, you must enable this service, and configure the correct server
address, port value, and domain name.
Server address: www.quickddns.com
Port number: 80
Test Click the Test button to test the DDNS configuration/network
connection.
Email Address The Honeywell applied-for DDNS has an expiration date. When
that expiration date is reached, the system sends an email prompt
to this email address.
Table 3-9 DDNS Configurations
Parameter Description
Configuration | 49
800-21261V3 - A - 05/2016
Domain name: There are two modes: Default domain name and customized domain name.
Except for the default domain name registration, you can also use a customized domain name.
After you have successfully registered a domain name, you can log in using it instead of the
device IP.
User name: Optional. Enter your email address.
IMPORTANT! Do not register frequently. You must wait at least 60 seconds between attempts at logging in.
Too many attempts might cause a server crash.
The system might take back a domain name if it is idle for one year. If your email is set up
correctly, you will get an email notification before the domain name is canceled.
Configuring the IP Filter
1. Click IP Filter under NETWORK to open the IP Filter configuration interface.
Figure 3-14 IP Filter Configuration Interface
2. Click to enable Trusted Sites, and only the listed IP addresses can access the current
NVR.
OR
Click to enable Blocked Sites, and the listed IP addresses can not access the current
NVR.
Adding Trusted or Blocked Sites
1. Click Add to open the Add configuration interface.
2. Select IP Address or IP Section from the drop-down menu.
3. Select IPv4 or IPv6 from the drop-down menu.
4. Enter the IP address in the IP address field.
5. Click Save.
www.honeywell.com/security
50 | Performance Series Full Poe Embedded NVR Remote User Guide
Configuring Email
Click Email under NETWORK to open the Email configuration interface.
Figure 3-15 Email Configuration Interface.
Table 3-10 Email Configurations
Parameter Description
Enable Click to enable the email function.
SMTP server Enter the email SMTP server IP.
Port Enter the corresponding port. Default is 25.
Anonymous Only available if the server supports the anonymity function.
This function allows you to automatically log in anonymously,
so you do not need to enter your user name, password, or
sender’s information.
User Name Enter the user name for logging in to the sender’s email box.
Password Enter the login password here.
Sender Enter the sender’s email address.
Encrypt Type Select from NONE, or SSL.
Title Enter an email subject. You can use up to 32 letters or
numbers.
Attachment Click to enable so that a snapshot can be attached to the
email.
Receiver Enter the receiver’s email address. You can enter up to 3 email
boxes. You can use SSL or TSL email boxes.
Configuration | 51
800-21261V3 - A - 05/2016
Configuring FTP
FTP allows you to configure settings for remote storage. Before you can enable FTP, you must
download or buy an FTP service tool. Refer to the Network Settings chapter of your User Guide
for more information.
Click FTP under NETWORK to open the FTP configuration interface.
Figure 3-16 FTP Configuration Interface
Interval The interval for sending ranges from 0 to 3600 seconds. 0
means that there is no interval.
Note The system will not send an email immediately when
the alarm occurs. When an alarm, motion detection, or
video abnormality triggers an email, the system sends
out the email according to the interval that is specified
here. This function is very useful when there are too
many emails activated by events, which might result in
an overload for the email server.
Health enable Click to enable the email health check. The NVR sends a test
email to check the network connection.
After enabling Health Enable, you can configure how
frequently the NVR sends out emails to test the network
connection.
Update Period (Interval) Allows the system to send out a test email to check the
connection.
Check the box to enable this function, and then set the
corresponding interval for the system to send out regular test
emails.
Test Click Test to send a test email. A popup message appears to
indicate the state of the network connection.
Table 3-10 Email Configurations
Parameter Description
www.honeywell.com/security
52 | Performance Series Full Poe Embedded NVR Remote User Guide
Click Test to test the FTP connection. A popup window shows the status of the connection.
Configuring UPnP
UPnP allows you to establish the mapping relationship between the LAN and the public network.
Here you can also add, modify, or remove a UPnP item.
Preparing for UPnP
1. In the Windows OS, click Start Control PanelAdd or remove programs.
2. Click Add/Remove Windows Components, and then select Network Services from the
Windows Component Wizard.
3. Click Details, then check Internet Gateway Device Discovery and Control client and
UPnP User Interface. Then click OK to begin the installation.
4. Enable UPnP from the internet. If your UPnP is enabled in the Windows OS, then the NVR
can automatically detect it through the My Network Places.
Configuring UPnP
1. Click UPnP in the NETWORK configuration interface to open the UPnP configuration
interface.
Table 3-11 FTP Configurations
Setting Description
Server IP Enter the IP address for the server.
Port Enter the Port number for the server.
Username Enter the user name for logging into the server.
Password Enter the password for logging into the server.
Anonymous Click to enable/disable anonymously logging into the server.
Remote Directory When the remote directory is null, the NVR automatically creates folders
according to the IP, time, and channel.
File Length Here you determine the size of the upload file. If the setup file size is
larger than the actual file, then the system uploads the entire file. If the
setup file size is smaller than the actual file, then the system uploads only
the set file size. If you enter 0 here, then the system uploads all
corresponding files.
Image Upload
Interval
This is the interval that the CVR waits through before uploading an image
to the FTP site. Select from 0 to 3600 seconds. 0 means that there is no
interval.
Channel Select a channel.
Weekday Select a weekday.
Time Periods You can configure up to two time periods per channel.
Recording Type Select from Alarm, Motion, or Regular.
Configuration | 53
800-21261V3 - A - 05/2016
Figure 3-17 UPnP Configuration Interface
2. Configure the following settings:
3. (Optional) Add, edit, or delete a mapping relationship from the Port Mapping List:
Add a mapping relationship: Click Add and then, in the Port Info dialog box, select the
Protocol (TCP or UDP), enter the Internal Port and External Port details, and then click
OK. To ensure data transmission, the internal and external ports should be the same.
Avoid using ports 1 to 255 or 256 to 1023.
Edit a mapping relationship: Click the mapping relationship that you want to edit, and
then, in the Port Info dialog box, edit the Service Name, Protocol, Internal Port, and/or
External Port details, and then click OK.
Delete a mapping relationship: Click the mapping relationship that you want to delete,
and then click Delete.
4. Click Apply to save your settings.
5. Click OK to exit the Setting menu.
Configuring SNMP
SNMP allows the communication between the network management work station software and
the proxy of the managed device. It is reserved for a third party developer.
Click SNMP under NETWORK to open the SNMP configuration interface.
Enable Click to enable or disable UPnP.
LAN IP Enter the NVR’s IP address from the TCP/IP page.
WAN IP Enter the router’s IP address.
www.honeywell.com/security
54 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-18 SNMP Configuration Interface
Table 3-12 SNMP Configurations
Configuration Description
SNMP Port The listening port of the proxy program of the NVR. It is a UDP
port, not a TCP port. This value ranges from 1 to 65535. The
default is 161.
Read Community This is a string, and it is a command between the managing
processes and the proxy process. Read Community defines
the authentication, the access control, and the management
relationship between one proxy and one managers’ group.
Ensure that the device and the proxy are the same. The Read
Community reads all the objects the SNMP supports in the
specified name. The default is Public.
Write Community This is a string, and it is a command between the managing
processes and the proxy process. It defines the
authentication, the access control, and the management
relationship between one proxy and one manager’s group.
Ensure that the device and the proxy are the same. The Write
Community reads, writes, and/or accesses all of the objects
the SNMP supports in the specified name. The default is
Write.
Trap Address The Trap information destination address from the device’s
proxy program.
Trap Port The Trap information destination port from the device’s proxy
program. The Trap port allows the gateway device and the
client-end PC in the LAN to exchange information.
SNMP Version If you check V1, then the system processes only the V1
information.
If you check V2, then the system processes only the V2
information.
Configuration | 55
800-21261V3 - A - 05/2016
Multicast
Multicast is a transmission mode for data packets. When there are multiple hosts to receive the
same data packets, multiple cast is the best option for reducing the bandwidth and the CPU
load. The source host can send out just one data for transit. This function also depends on the
relationship of the group member and the router group.
1. Click Multicast under NETWORK to open the Multicast configuration interface.
Figure 3-19 Multicast Configuration Interface
2. Select Enable to enable multicast.
3. Enter a multicast IP address in the IP Address box. The address must be valid for
multicasting and should be in the range 224.0.0.0 to 239.255.255.255 for IPv4 or have the
prefix ff00::/8. An address in the range 239.252.0.0 to 239.255.255.255 is recommended.
4. Enter a multicast port number in the Port box, or use the default setting (36666).
5. Click Apply to save your settings.
6. Click OK to exit the Setting menu.
Auto-Registration
Auto Register allows the device to automatically register to the proxy you have specified. This
allows you to use the client-end to access the NVR through the proxy. The proxy acts as a
switch. In network service, the device supports IPv4 server addresses or domains.
1. Click Auto Register under NETWORK to open the Auto Register configuration interface.
www.honeywell.com/security
56 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-20 Auto Register Configuration Interface
2. Click to enable Auto Registration.
3. Enter a Proxy Server IP, Port, and Sub device ID.
4. Click to enable Auto Registration.
5. Then click Save.
Alarm Centre
You can connect your alarm platform to the NVR’s Alarm Center to develop alarm functions.
When a local alarm occurs, the NVR system can upload alarm signals to the Alarm Centre.
Before using the Alarm Centre, you must configure the server IP, Port, and Protocol Type.
When an alarm occurs, the NVR system can send data, as defined by the protocol, to the client.
1. Click Alarm Center under NETWORK to open the Alarm Center configuration interface.
Figure 3-21 Alarm Centre Configuration Interface
Configuration | 57
800-21261V3 - A - 05/2016
HTTPS
With these settings, you can ensure that the PC successfully logs in through HTTPS to
guarantee communication data security. This reliable and stable technology can secure user
information and device safety.
Note If you have changed the device’s IP, then you’ll need to implement the server
certificate again.
Note If this is your first time to use HTTPS on your PC, then you’ll need to download
the root certificate.
HTTPS Configuration Overview
1. Click HTTPS under NETWORK to open the HTTPS configuration interface.
Figure 3-22 HTTPS Configuration Interface
2. Create a Server Certificate if the is the first time you are using this function. See Creating
a Server Certificate on page 57.
OR
Download an already established root certificate. See Downloading a Root Certificate on
page 58.
3. View and set the HTTPS port. See Viewing and Setting the HTTPS Port on page 61.
4. Open the Login interface through the browser. Login Configurations on page 61.
Creating a Server Certificate
Follow these steps if this is the first time you are using this function.
1. Click to open the Create Server Certificate window.
www.honeywell.com/security
58 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-23 Create Server Certificate Window
2. Enter a Country name, a State, a City, Organization, etc, then click Create.
A message appears to confirm that you have succeeded in creating a new server
certificate.
Figure 3-24 Server Certificate Confirmation Message
Downloading a Root Certificate
1. Click to open a File Download - Security Warning window.
Figure 3-25 File Download Warning
2. Click Open to open the Certificate window.
Configuration | 59
800-21261V3 - A - 05/2016
Figure 3-26 Certificate Window
3. Click Install Certificate to open the Certificate Import Wizard.
Figure 3-27 Certificate Import Wizard
4. Click Next to open the Certificate Store window.
www.honeywell.com/security
60 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-28 Certificate Import Wizard - Certificate Store Window
5. Select a location for the certificate.
6. Click Next to complete the process. A message appears to let you know the process is
complete.
Figure 3-29 Certificate Import Wizard - Completion Message
7. Click Finish, and a security warning pops up.
Configuration | 61
800-21261V3 - A - 05/2016
Figure 3-30 Security Warning
8. Click Yes. When the installation is complete, a confirmation message appears.
Figure 3-31 Certificate Import - Confirmation Message
Viewing and Setting the HTTPS Port
Click Connection under Network to open the Connection interface.
Figure 3-32 Connection Interface
Login Configurations
1. Open the browser, then enter https://xx.xx.xx.xx:port, where xx.xx.xx.xx is your device’s
IP or domain name.
The port is your HTTPS port. If you are using 443 (the default HTTPS value), then you do
not need to add port information here.
2. Enter https://xx.xx.xx.xx to access.
If you have the correct settings, then you should see the login interface.
www.honeywell.com/security
62 | Performance Series Full Poe Embedded NVR Remote User Guide
Configuring Switch Settings
You can change the IP Address, Subnet Mask, and Default Gateway for setting the PoE switch
settings.
1. Click Switch under Network to open the Switch interface.
Figure 3-33 Switch Configuration Interface
2. Configure the following settings:
3. Click Apply to save your settings.
Configuring Event Settings
Configuring Video Detection
Motion Detection Configurations
You can configure the system to generate a motion detection alarm when the minimum amount
of motion (as defined by you) is detected in the video.
Click Detect under EVENT to open the Motion Detect configuration interface.
Table 3-13 Switch Configurations
Configuration Description
IP Address Enter a new IP address.
Subnet Mask Enter a new subnet mask.
Default Gateway Enter a new default gateway.
Configuration | 63
800-21261V3 - A - 05/2016
Figure 3-34 Motion Detect Configuration Interface
www.honeywell.com/security
64 | Performance Series Full Poe Embedded NVR Remote User Guide
Table 3-14 WEB - Motion Detection Configurations
Configuration Description
Enable Click to enable motion detection. Select a channel from the
drop-down list.
Period Define a period during which motion detection is active.
1. Click Set. The Set configuration interface appears.
2. Select a day of the week from the drop-down menu. Select
from a day of the week, Work Day, or Free Day.
Note If you select Work Day or Free Day, a Set button
appears so you can configure which days are Work
Days and which days are Free Days. Click Set, select
the Work Days and the Free Days, then click OK.
Note You can configure up to 6 periods within one day.
3. Configure a time range for when the event detection area
is active, then click the check box to select that time range.
4. Click Save.
Configuration | 65
800-21261V3 - A - 05/2016
Region 1. Select a motion detection type.
2. Click Set. The Motion Detection Set configuration
interface appears.
3. Select the event detection area by left-clicking and
dragging the mouse.
There are 396 (PAL) or 330 (NTSC) small zones.
Green: Indicates the current cursor position.
Grey: Indicates the event detection zone.
Black: Indicates a disarmed zone.
4. Select a Sensitivity, from 1 to 100. The higher the number,
the higher the sensitivity.
5. Click Save to save the configurations. Click Esc to exit the
setup without saving the changes.
Record Channel The system automatically starts recording selected channels
when a motion detection alarm occurs.
Note You need to set the motion detection recording period.
Go to Storage
Schedule to configure the current channel
for scheduled recording. Refer to the User Guide for more
information about Configuring Recording Schedule
Storage Settings.
Delay The system can delay recording for a specified amount of time
after an alarm has ended. Select from 10s to 300s.
Alarm Out Select the device output port, 1 or 2. Select the corresponding
port(s) so the system can activate the corresponding alarm
devices when an alarm occurs.
Latch The system can delay the alarm output for a specified time
after an alarm ends. The value ranges from 1s to 300s.
Table 3-14 WEB - Motion Detection Configurations
Configuration Description
www.honeywell.com/security
66 | Performance Series Full Poe Embedded NVR Remote User Guide
Video Loss Detection Configurations
You can configure the system to generate a video loss alarm when the minimum amount of
video loss (as defined by you) is detected in the video.
PTZ Activation When PTZ activation is configured, the system can activate
PTZ operation when an alarm is detected.
1. Click Setup to open the PTZ Activation configuration
interface.
2. Select a preset, tour, or pattern from the drop-down menu.
3. Click Save.
Tour Click to enable a tour to be triggered by an alarm. The system
supports 1/8-window tour. Refer to the User Guide for more
about tour interval setup. On the Display Settings tab, when
there are two tours enabled by default, you can configure the
system so an alarm triggers the system to enable the alarm
tours you configured here. If there is no alarm, then the system
uses the tour setup that was configured in the Display
interface.
Snapshot Click to enable the Snapshot function. Channel snapshots
are taken according to the schedule you configure. Alarm
snapshots are taken when an alarm occurs.
Show Message Click to enable a pop-up message on your local host PC
screen to let you know an alarm has occurred.
Send Email The system can send an email when an alarm is detected.
When you have enabled the Snapshot function, the system
can also send an image attached to the email. Go to
Network
Email to configure the email settings. Refer to the
User Guide for more information.
Alarm Upload Enable this function, and when a motion event is detected, an
alarm message is uploaded to the NVR.
Buzzer Click to enable the Buzzer function. When an alarm occurs,
the buzzer beeps.
Table 3-14 WEB - Motion Detection Configurations
Configuration Description
Configuration | 67
800-21261V3 - A - 05/2016
Note Video loss does not support anti-dither, sensitivity, or region setup.
Click Video Loss under DETECT to open the Video Loss configuration interface.
Figure 3-35 Video Loss Configuration Interface
The configuration for Video Loss Detection is very similar to the configuration for Motion
Detection. Please see Motion Detection Configurations on page 62 for more information.
Camera Masking Detection Configurations
You can configure the system to generate a camera tampering alarm when the minimum
amount of tampering (as defined by you) is detected in the video.
Click Camera Masking under DETECT to open the Camera Masking configuration interface.
Figure 3-36 Camera Tampering Configuration Interface
www.honeywell.com/security
68 | Performance Series Full Poe Embedded NVR Remote User Guide
The configuration for Camera Tampering Detection is very similar to the configuration for
Motion Detection. Please see Motion Detection Configurations on page 62 for more
information.
Configuring Alarms
Before alarm operation, you should check that you have properly connected all alarm devices,
such as buzzers and flashing lights.
Configuring Local Alarms
Click ALARM under EVENT to open the Local Alarm configuration interface.
Figure 3-37 WEB - Alarm Configuration Interface
Configuration | 69
800-21261V3 - A - 05/2016
00Configuring Net Alarms
Table 3-15 WEB - Alarm Configurations
Configuration Description
Enable Click to enable alarms. Select a channel from the drop-down
list.
Period Define a period during which the alarm is active.
1. Click Set. The Set configuration interface appears.
2. Select a day of the week from the drop-down menu. Select
from a day of the week, Work Day, or Free Day.
Note If you select Work Day or Free Day, a Set button
appears so you can configure which days are Work
Days and which days are Free Days. Click Set, select
the Work Days and the Free Days, then click OK.
Note You can configure up to 6 periods within one day.
3. Configure a time range for when the event detection area
is active, then click the check box to select that time range.
4. Click Save.
Type Select either NO or NC.
Record Channel The system automatically starts recording selected channels
when a motion detection alarm occurs.
Note You need to set the alarm recording period.
Go to Storage
Schedule to configure the current channel
for scheduled recording. See Configuring Local Storage on
page 76.
Delay The system can delay recording for a specified amount of time
after an alarm has ended. Select from 10s to 300s.
Alarm Out Select the device output port, 1 or 2. Select the corresponding
port(s) so the system can activate the corresponding alarm
devices when an alarm occurs.
Latch The system can delay the alarm output for a specified time
after an alarm ends. The value ranges from 1s to 300s.
www.honeywell.com/security
70 | Performance Series Full Poe Embedded NVR Remote User Guide
Network Alarm are the alarm signals from the TCP/IP. You cannot select the sensor type or
anti-dither functions.
Click Net Alarm in the ALARM configuration interface.
PTZ Activation When PTZ activation is configured, the system can activate
PTZ operation when an alarm is detected.
1. Click Setup to open the PTZ Activation configuration
interface.
2. Select a preset, tour, or pattern from the drop-down menu.
3. Click Save.
Tour Click to enable a tour to be triggered by an alarm. The system
supports 1/8-window tour. See Configuring Display Settings
on page 80 for tour interval setup. On the Display Settings
tab, when there are two tours enabled by default, you can
configure the system so an alarm triggers the system to
enable the alarm tours you configured here. If there is no
alarm, then the system uses the tour setup that was
configured in the Display interface.
Snapshot Click to enable the Snapshot function. Channel snapshots
are taken according to the schedule you configure. Alarm
snapshots are taken when an alarm occurs.
Show Message Click to enable a pop-up message on your local host PC
screen to let you know an alarm has occurred.
Send Email The system can send an email when an alarm is detected.
When you have enabled the Snapshot function, the system
can also send an image attached to the email. Go to Main
Menu
SettingNetworkEmail to configure the email
settings. See Configuring Email on page 50.
Alarm Upload Select the check box to enable the system to upload an alarm
signal to the network (including to an alarm center and/or web
client).
Buzzer Click to enable the Buzzer function. When an alarm occurs,
the buzzer beeps.
Table 3-15 WEB - Alarm Configurations
Configuration Description
Configuration | 71
800-21261V3 - A - 05/2016
Figure 3-38 WEB - Net Alarm Configuration Interface
Configuring Alarm Outputs
1. Click Alarm Output under SETTING to open the Alarm Output configuration interface.
Figure 3-39 WEB - Alarm Output Configuration Interface
2. Click to enable the alarm output for each alarm. Select from Schedule, Manual, or Stop,
and Status.
3. Click Save to save these settings and return to the previous menu.
Configuring for Abnormalities
Click Abnormality under EVENT to open the Abnormality - No Disk configuration interface.
Figure 3-40 WEB - Abnormality Configuration Interface
www.honeywell.com/security
72 | Performance Series Full Poe Embedded NVR Remote User Guide
There are six types of abnormalities:
No Disk
•Disk Error
No Space
Net Disconnection
•IP Conflict
•MAC Conflict
You can configure how the system responds to each kind of abnormality. The configuration is
similar for each type.
Figure 3-41 Configuring for Abnormalities
Configuration | 73
800-21261V3 - A - 05/2016
Configuring Storage
Configuring Storage Schedules
You can add or remove schedules for recording.
There are four recording modes: General (auto), Motion Detect, Alarm, and MD&Alarm. You
can configure up to six periods per day.
1. Click Schedule under STORAGE to open the Schedule configuration interface.
Table 3-16 Configuring for Abnormalities
Configuration Description
Event Type Select from No Disk, Disk Error, Disk No Space, Net
Disconnection, IP Conflict, and MAC Conflict.
Less Than: (For No Space configuration only) Configure the
minimum percentage of free space on the disk. An alarm lets
you know when the disk capacity is low. You need to click to
enable this function.
Enable Click to enable this function.
Alarm Out Select the device output port, 1 or 2. Select the corresponding
port(s) so the system can activate the corresponding alarm
devices when an alarm occurs.
Latch The system can delay the alarm output for a specified time
after an alarm ends. The value ranges from 1s to 300s.
Show Message Click to enable a pop-up message on your local host PC
screen to let you know an alarm has occurred.
Send Email The system can send an email when an alarm is detected.
When you have enabled the Snapshot function, the system
can also send an image attached to the email. Go to Main
Menu
SettingNetworkEmail to configure the email
settings. Refer to the User Guide for more information.
Buzzer Click to enable the Buzzer function. When an alarm occurs,
the buzzer beeps.
www.honeywell.com/security
74 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-42 Schedule Configuration Interface
The schedules are color-coded by type:
Green: General recording/snapshot.
Yellow: Motion detection recording/snapshot.
Red: Alarm recording/snapshot.
Blue: MD&Alarm recording/snapshot.
Table 3-17 Scheduled Storage Settings
Setting Description
Channel Select a channel from the drop-down list
Pre-record Enter a pre-recording time here. Select from 0 to 30.
Redundancy You can configure the NVR to backup recorded files onto two
different HDDs. Click to enable.
Note Before you can enable this function, you must
configure at least one HDD as redundant. Go to Main
Menu
SettingStorageHDD Management).
This function is not available if there is only one HDD.
Snapshot Click to enable Snapshot.
Holiday Click to enable Holiday.
Configuration | 75
800-21261V3 - A - 05/2016
2. Click Setup. The Setup configuration interface opens.
Figure 3-43 Set Configuration Interface
Setup (Sunday to
Saturday)
Click Setup, then set a recording period. See step 2 below.
You can configure up to six periods in one day. If you do not
click a day at the bottom of the Setup interface, then the
changes you make are for today.
Setup (Holiday) Click Setup, then set a recording period. See step 2 below.
You can configure up to six periods in one day. If you click
Holiday at the bottom of the Setup interface, then the
currently selected channel will record according to these
holiday settings.
Copy Allows you to copy a channel’s setup to one or more other
channels. Click Copy in the Configuration interface to open
the Copy interface.
Select channels to which to copy the current configurations,
then click Save.
Table 3-17 Scheduled Storage Settings
Setting Description
www.honeywell.com/security
76 | Performance Series Full Poe Embedded NVR Remote User Guide
3. Configure the schedule, then click Save.
4. Click Save to save the settings, and then click Save to save the Schedule configuration.
Configuring Local Storage
Click Storage under STORAGE to open the Local Storage configuration interface.
The Local Storage interface shows HDD information. You can also configure read-only,
read-write, redundancy (if there is more than one HDD), and format settings.
Figure 3-44 Local Storage Interface
Configuring Manual Recording Storage Settings
Click Record under Storage to open the Record configuration interface.
Table 3-18 Schedule Configurations
Configuration Description
Channel Select a channel from the drop-down list.
Regular Check to enable the Regular schedule mode.
Motion Check to enable the Motion Detection schedule mode.
Alarm Check to enable the Alarm mode.
MD&Alarm Check to enable the MD&Alarm mode.
Configuration | 77
800-21261V3 - A - 05/2016
Figure 3-45 Manual Recording Storage Interface
Configuring General Settings
General Settings
Click General under SETTING to open the General settings configuration interface.
Table 3-19 Recording Storage Interface
Setting Description
Channel See the channel numbers, including the maximum number of
channels.
Auto Select Schedule, and the system enables the automatic
recording function as you set it in the Recording Schedule
Setup: General, Motion Detection, or Alarm. See
Configuring Storage Schedules on page 73.
Manual This is the highest priority. Enable the corresponding channel
to record not matter what period was applied in the
Recording Setup.
Off Stop recording the current channel no matter what recording
setup is applied to that channel.
Start All/Stop All Click the All button, and then enable or disable recording on
all channels.
www.honeywell.com/security
78 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-46 General Settings Interface
Date and Time Settings
Click the Date & Time tab in the GENERAL configuration interface to open the Date & Time
configuration interface.
Table 3-20 General Settings Configurations
Configuration Description
Device Name Enter a device name.
Device No. Enter a channel number.
Language Select a GUI language from the drop-down list.
Note You need to reboot the device/NVR to activate this
change.
Video Standard Select the video standard, either NTSC or PAL.
HDD Full Select what happens when the NVR’s storage is full. Select
either Stop Recording or OverWrite.
Stop Recording: If the HDD is full, the NVR stops recording.
OverWrite: If the currently working HDD is full and the next
HDD is also full, the NVR overwrites the previous files.
Pack Duration Select the recording duration. Select from 1 to 60 minutes.
The default is 60 minutes.
Configuration | 79
800-21261V3 - A - 05/2016
Figure 3-47 Date & Time Configuration Interface
Holiday Settings
1. Click the Holiday Setup tab in the GENERAL settings configuration interface to open the
Holiday Setup configuration interface.
Table 3-21 Date & Time Configurations
Configuration Description
Date Format Select the date format from the drop-down list.
Time Format Select from either 24 hour or 12 hour.
Date Separator Select from a period (.), a hyphen (-), or a slash (/).
System Time Set the NVR’s time. You have to Save to activate this setting.
Sync PC Click to synchronize your NVR’s time with your PC’s time.
Time Zone Select a Time Zone for the NVR.
DST Click to enable Daylight Saving Time (DST). Click to select a
type, either Date or Week. Then configure a date and time
when DST begins and ends.
NTP Click to enable the NTP server.
NTP Server Enter the NTP time server address.
Port Enter the NTP time server port.
Upgrade
Period/Interval
Configure the synchronization period between the NVR and
the NTP time server.
www.honeywell.com/security
80 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 3-48 Holiday Settings Configuration Interface
2. Click Add New Holiday to add a holiday, enter the holiday details, then click Save.
Configuring Display Settings
Display/GUI Settings
Click Display under SETTING interface to open the Display/GUI settings configuration
interface.
Figure 3-49 Display Configuration Interface
Table 3-22 GUI Configurations
Configuration Description
Resolution Select from four options: 1920x1080, 1280x1024 (default),
1280x720, and 1024x768.
Note You need to reboot the NVR to activate changes to the
resolution.
Transparency Configure the transparency of the GUI display. Select from
128 to 255.
Time Display/Channel
Display
Click to enable these functions, which display the time and
channel on the video monitor.
Configuration | 81
800-21261V3 - A - 05/2016
Tour Configurations
In the Tour interface, you can set the Tour Interval, Split mode, Motion Detection Tour, and
Alarm Tour modes.
Click the Tour tab in the DISPLAY configuration interface under SETTING to open the Tour
configuration interface.
Figure 3-50 Tour Configuration Interface
Image Enhance Check to enable Image Enhance, to optimize the preview
video.
Auto Logout Enter the how long the NVR waits before automatically
logging the user out.
Startup Wizard Click to enable the Startup Wizard on restarting or starting up
the NVR.
Navigation Bar Click to enable/disable the navigation bar.
Original Scale Click Set to select to show channels in their original aspect
ratio. Unselected channels display in full screen.
Table 3-22 GUI Configurations
Configuration Description
Table 3-23 Display Tour Settings
Setting Description
Enable Tour Check to enable this function.
Interval Adjust the transparency. Select from 5s to 120s. The default
is 5s.
www.honeywell.com/security
82 | Performance Series Full Poe Embedded NVR Remote User Guide
RS232 Configurations
1. Click RS232 under SETTING to open the RS232 configuration interface.
Figure 3-51 WEB - RS232 Configuration Interface
2. Make your selections, then click Save.
Configuring PTZ Settings
Before configuring PTZ, please ensure the following:
The PTZ and decoder are connected correctly, and that the decoder address setup is
correct.
That the correct decoder line is connected to the correct NVR line (A to A; B to B).
Window Split Set the window mode and channel group. Depending on your
NVR, it can support up to a 1/4/8/9/16-window split.
Channel Group Add channels to a channel group, and when the NVR starts a
tour, the tour starts only on the selected channels for the
group.
Motion Tour/Alarm Tour
Type
Set the Motion Detection Tour and Alarm Detection Tour
window modes. The NVR can support 1/8 window.
Table 3-23 Display Tour Settings
Setting Description
Table 3-24 RS232 Web Configurations
Setting Description
Function Select the corresponding dome Protocol. The default is
Console.
Baud Rate Select the Baud Rate. The default is 115200.
Data Bit Select from 5 to 8. The default is 8.
Stop Bit Choose either 1 or 2. The default is 1.
Parity Select from None, Odd, Even, Space, or Mark. The default is
None.
Configuration | 83
800-21261V3 - A - 05/2016
Click PAN/TILT/ZOOM under SETTING to open the PAN/TILT/ZOOM configuration interface
Figure 3-52 PAN/TILT/ZOOM Configuration Interface
Accounts
Some Basic User and Group Rules
You can use up to 6 characters for user names and group names. You can not use a
space at the beginning or end of a name. You can use characters, numbers, and an
underline (_).
You can add up to 64 users and 20 groups (these are also the default settings). The
default setting includes two group levels: user and admin. Configure the Group privileges,
and then assign users to their groups according to the privileges those users require.
User management involves assigning privileges to groups, and users to groups. User
names can not be the same as group names; user names and group names must be
unique. Users can belong to only one group.
Click Account under SETTING to open the Account settings configuration interface.
Table 3-25 PAN/TILT/ZOOM Configuration Interface
Setting Description
Channel Select a channel.
PTZ Type Select Remote for the PTZ type. A remotely connected IP
camera is connected through the network.
www.honeywell.com/security
84 | Performance Series Full Poe Embedded NVR Remote User Guide
User Name
Figure 3-53 User Name Account Configurations
There are two default users:
•admin
a hidden user
The hidden default user is for internal use only, and can not be deleted. If users log in without
selecting a login user, the hidden default user is automatically used. You can configure some
rights for the default hidden user, such as monitor rights so that the user can view channels
without logging in.
Note User rights can not exceed group rights.
TIP! General users should have fewer rights than administrators.
Adding a User
1. Click Add User. The Add User configuration interface opens.
Configuration | 85
800-21261V3 - A - 05/2016
Figure 3-54 Add User Configuration Interface
2. Enter a Username and a Password. Re-enter the Password to confirm it.
3. Select a Group.
4. Select System, Playback, and Real-Time Monitor privileges.
5. Click Save to save these new settings.
Modifying a User
1. Click under Modify to open the Modify User configuration interface.
Figure 3-55 Modify User Configuration Interface
www.honeywell.com/security
86 | Performance Series Full Poe Embedded NVR Remote User Guide
2. Change the settings, then click Save.
Modifying a Password
1. Click Modify Password in the Modify User configuration interface.
2. Enter the old Password, then enter the new Password twice.
3. Click OK to save the new password.
Note Passwords can have up to 6 characters, numbers only. Users with admin rights
can modify the password of other users.
Groups
Click the Group tab in the Account configuration interface to open the Group configuration
interface.
Figure 3-56 Group Configuration Interface
Adding a Group
1. Click Add Group in the Group Account configuration interface.
Figure 3-57 Add Group Configuration Interface
Configuration | 87
800-21261V3 - A - 05/2016
2. Enter a Group name.
3. Select System, Playback, and Real-time Monitor privileges.
4. Click Save to save these new settings.
Modifying a Group
1. Click under Modify to open the Modify Group configuration interface.
Figure 3-58 Modify Group Configuration Interface
2. Modify the Group privileges, then click Save to save the changes.
Automatic Maintenance
1. Click Auto Maintain under SETTING to open the Auto Maintain configuration interface.
Figure 3-59 Auto Maintain Configuration Interface
www.honeywell.com/security
88 | Performance Series Full Poe Embedded NVR Remote User Guide
2. Select when the NVR automatically reboots, both day and time.
3. Select when the NVR automatically deletes old files.
4. Click Save to save the new settings.
Note Click Manual Reboot to manually reboot the NVR.
Import/Export
Click Config Backup under SETTING to open the Import/Export configuration interface.
Figure 3-60 Import/Export Interface
Default
You can select to return Channel, Network, Event, Storage, and/or System settings to their
defaults.
1. Click Default under SETTING to open the Default configuration interface.
Figure 3-61 Default Settings Interface
Table 3-26 Import/Export Operations
Activity Description
Import Use to import local setup files to the NVR system.
Export Use to export the corresponding WEB setup to your local PC.
Configuration | 89
800-21261V3 - A - 05/2016
2. Click to select, or select All, then click Default.
Upgrade
Click Upgrade under SETTING to open the Upgrade configuration interface.
Figure 3-62 Upgrade Interface
1. Click Browse, then click to select the upgrade file.
2. Click Upgrade to begin the update.
The file name will end with .bin.
Note During the upgrade process, do not unplug the power cable, network cable, or
shut down the device.
CAUTION An improper upgrade program could result in a device
malfunction.
www.honeywell.com/security
90 | Performance Series Full Poe Embedded NVR Remote User Guide
800-21261V3 - A - 05/2016
4
Playback 4
This chapter includes descriptions of the following:
Playing back recorded video
Downloading recorded video
Playback
1. Click the Playback tab at the top of the Main window.
The Playback interface appears.
www.honeywell.com/security
92 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 4-1 Playback Interface
2. Select a recording type, recording date, window display mode, and channel name to
select video for playback.
3. Click File List, and the system displays a list of recorded video clips that match the search
criteria from step 2.
Figure 4-2 List of Recorded Video Clips
Video clips
Playback | 93
800-21261V3 - A - 05/2016
4. Select a file from this list for playback, then click Play (). You can play back in full screen
mode.
Use the playback control bar to control playback.
Figure 4-3 Playing Back Video
Note For one-channel playback, the system can not play back and download at the
same time.
Downloading Video
After generating a list of recorded video clips by clicking File List, select the files you want to
download, then click Download.
www.honeywell.com/security
94 | Performance Series Full Poe Embedded NVR Remote User Guide
Figure 4-4 Downloading Recorded Video
The Download button becomes the Stop button, and it indicates the downloading progress (in
a percentage).
Go to your default Saved Path file to view the downloaded files. See Configuring the Save Path
on page 39.
Loading More
Click More in Fig 13-94, and the Download by File/Download by Time interfaces appear.
Playback | 95
800-21261V3 - A - 05/2016
Figure 4-5 Download by File/Download by Time Interfaces
In this window, you can search for recordings or snapshots. Select the channel, recording type,
and the recording time.
www.honeywell.com/security
96 | Performance Series Full Poe Embedded NVR Remote User Guide
800-21261V3 - A - 05/2016
5
Alarms 5
This chapter describes how to remotely activate the alarms.
Activating Alarms
Click the Alarm tab at the top of the Main window. The Alarm configuration interface appears.
Note For information about configuring alarms, refer to the User Guide.
www.honeywell.com/security
100 | Performance Series Full Poe Embedded NVR Remote User Guide
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell HEN16122 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HEN16122 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell HEN16122

Honeywell HEN16122 User Manual - English - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info