Manual Honeywell HCE322 (page 3 of 21) (English, French, Spanish)

723878

Zoom out

Zoom in

1/21

SET UP

MOVING THE HEATER

• The Honeywell Ceramic Tower Heater requires no assembly. Simply unpack heater and save all packaging materials for o-

season storage.

• Place the heater on a rm, level, open surface free from obstructions and at least 3 feet (0.9m) away from any wall or

combustible material.

• DO NOT use on an unstable surface such as bedding or deep carpeting.

• BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY BE TRIPPED OVER BY CHILDREN OR PETS.

• This heater is equipped with a Cool Touch handle for your convenience.

• Turn o the heater.

• Allow it to cool for ten minutes.

• Unplug heater and move.

OPERATION

• NOTE: NEVER LEAVE AN OPERATING UNIT UNATTENDED

• With heater in the OFF position ( ), plug the heater into

a polarized 120V outlet. DO NOT FORCE THE POLARIZED

PLUG INTO THE OUTLET; it will only t one way.

• With 80° oscillation, the Honeywell Ceramic Tower Heater

is versatile and designed to be placed in the center of the

room or closer to the wall (at least 3 feet way) for maximum

convection room heating.

• Turn heater on by pressing the Power Button ( ).The Power

Indicator will illuminate and the heater will start in the

Constant On HI Level Setting ( ).

• The heater has two operational modes – continuous heating

or heating with a thermostat setting where the heater cycles

on and o according to the selected temperature setting.

• To set a Continuous Heat Setting, press ( ): - Choose Low ( ) to use 900 watts of power (750 watts on the HCE317 Series only)

- Choose High ( ) to use 1500 watts of power

NOTE: Because the Low setting does not require as much electricity to operate, it is more energy ecient and may be a better

option if you are concerned about saving energy.

• In the continuous heat mode, make sure to manually turn the heater OFF when done using this appliance.

• To set the Thermostat, press the Thermostat Control Buttons ( ) and choose your Desired Temperature. The Desired

Temperature will ash ve times and then the Current Temperature in the room will display as a steady red. On the HCE305/HCE309

unit models only, there are 4 pre-set comfort settings from which to choose: 65°, 70°, 75°, 80°. These are your desired

room temperature settings.

NOTE: If the Current Temperature is higher than your Desired Temperature, the heater will be o until the room temperature falls

below this setting or until the Desired Temperature is changed.

• Press the Timer Button ( ) to select 1, 2, 4, or 8 hour setting. The heater will run for that chosen period in the selected mode,

counting down the hours and automatically shutting the heater o after the selected time has passed.

• If unit has an oscillation feature, press the Oscillate Button ( ) to turn on or o the oscillation function.

• To shut the heater o, press the Power Button ( ) and the heater will begin Powering Down. The heater will shut o after counting

down 6 seconds in the Temperature Display to cool down the internal components.

• It is important to allow the heater to run through the cool down phase. DO NOT unplug the heater until it has completed the cool

down cycle.

Oscillate Button

Fig. 1

Power

Button

Timer

Thermostat

Control Buttons

Current Temperature/

Desired Temperature Display

Heat Level Settings

Power

Indicator

Note: Controls/features will vary slightly by model

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell HCE322 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell HCE322 Manual

Product: