680984
27
Zoom out
Zoom in
Previous page
1/53
Next page
Power up and bind an Underfloor Heating
Controller (HCE80 or HCC80)
If you want to control the zone temperature with your
evohome Controller (the evohome Controller needs
to be located in that zone) press YES, otherwise press
NO and bind a sensor – either Digital Room Thermostat
(DTS92) or Room Temperature Sensor (HCW82/HCF82).
To bind the Digital Room
Temperature Sensor (DTS92)
1
Press and hold the power button for 2
seconds to put the unit into standby
2
Press the up and down arrows together for
three seconds – it should say INst
3
Press the down arrow – it should say COnt
4
Press the up arrow three times – it should say CLr
5
Press the power button once to clear
any previous binding data
6
Press the up arrow – it should say COnt
7
Press the power button once to send the
binding signal to the evohome Controller
8
You should receive a SUCCESS message on the
evohome Controller (if not go back and re-bind)
Make sure the zone
you’re adding on the
evohome Controller
corresponds to the
correct underfloor
heating zone.
!
If you are NOT
following GUIDED
CONFIGURATION
follow these steps
on your evohome
Controller display once
the underfloor heating
controller and sensors
have been fitted:
1. On the evohome
Controller press and
hold “Settings”
for
3 seconds
2. Press the green tick
3. Press ADD A ZONE
4. Press the zone
you’re adding the
controller to then
select UNDERFLOOR
HEATING
5. You need to install
a sensor (HCW82,
HCF82, DTS92) in
each zone controlled
by the underfloor
heating controller
and bind it to the
evohome Controller.
You need to repeat this
process for every zone
that uses underfloor
heating.
evohome
Controller
HOLD
3 SEC
2
Underfloor Heating Controller (HCE80 or HCC80)
24 Step 3: Power up and bind devices
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Evohome ATF200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Evohome ATF200 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell Evohome ATF200

Honeywell Evohome ATF200 Installation Guide - Dutch - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info