32341
7
Zoom out
Zoom in
Previous page
1/14
Next page
—-.
A quick guide for operating or making changes follows:
NOTE: System switch must be set to Heat or Cool to perform the following:
Temp
u
Warmer
Temporarily Change Temperature for Current Period
Only—
n
. Temporary indicator will
Cmlar
o
show on display; it will cancel itself at next scheduled change. To cancel sooner, press
P~&
Temp
n
u
Warmaf
Hold a Temperature Indefinitely—
~~~P
,
0
0
;
press
pJ&
to cancel.
Coobr
14
---
.—
.
n
Check Current Temperature Setting-
p;~~m
.
(If
using Temporarily Change
or
Hold,
pressing this will cancel your change.)
D
Check Programs— ~~Uk
o
Run
repeatedly to see each time and temperature; then Program .
Time
(
1
c1
Cancel a Program-
~~~Ub
until program to cancel shows; then
H
together.
o
Beck
Permanently Change a Program—Repeat steps
under Heating Program or Cooling Program
(pages 12 and 13) as applicable.
u
Return
to
normal program or start program —
p;~~m
.
~m
:
Customer Assistance
_
Adjust Fan Operation Switch, As Required
D
The thermostat fan operation switch, labeled
electric heat system, set the switch to “E. The
FUEL SWITCH (see illustration on page 17) is
“E setting will allow the fan to turn on
immedi-
factory-set in the “F position. This is the correct
ately
with the heating or cooling in a system
setting for most systems. If your system is an
where the “G” terminal is connected.
_
Adjust System On-Time, As Required
El
The system on-tim
e
is
facto-~-set
for a warm
air, gas or oil heating system. If you are installing
it on another type of system, the system on-time
must be adjusted accordingly by setting screws A
and B on the back of the thermostat. Use the
heating system table shown in the illustration,
(page 17) as a guide. The system on-time should
be optimized according to the type of system to
minimize room temperature swings. Setting the
screw “out one turn” means turning the screw
approximately 360° counterclockwise, or about
one complete turn.
In the unlikely event that you want longer furnace
on-time, readjust screws A and/or B as follows:
First, turn both screws
in
completely, then adjust
for system type:
Warm Air Furnace-Set at the Hot Water
setting, (A - out one turn, B - in).
Electric Furnace-Leave at the Warm Air
Furnace setting (A - in, B - in).
16
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell CT2400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell CT2400 in the language / languages: English as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell CT2400

Honeywell CT2400 User Manual - French - 40 pages

Honeywell CT2400 User Manual - Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info