445195

Honeywell CM67RF Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
How do I know when the batteries need changed
and how do I change them?
Your RF Chronotherm has built-in electronics that constantly monitor
the battery power level. With no other accessories fitted the batteries
should last about 3 years. When the batteries need replaced, a
flashing symbol will be displayed.
To change the batteries:
1. Lift up the front flap to reveal the battery compartment. Open the
battery compartment by inserting a coin underneath the bottom
right edge of the flap and lift it out.
2. Replace the used batteries with 2 new AA LR6 Alkaline Batteries
(Duracell are recommended) and push the battery compartment
firmly back into the front of the unit.
RESPECT YOUR ENVIRONMENT!
Take care to dispose of used batteries carefully.
The RF Chronotherm has a permanent memory to keep your program
settings while you change the batteries, you should never need to
reprogram. However, if you take more than one minute to change
them, you may need to correct the time by moving the slider to the
DAY / position and pressing the + button.
I want to use the table stand instead of wall mounted
bracket. Where can I position the room unit?
It is important to keep the room unit in a location where reliable RF
communication was proven. Advise your installer where would you like
to position the room unit and he will check if the RF communication is
reliable in the selected location(s).
How do I remove the RF Chronotherm from the
table stand or wall bracket?
After programming is finished always replace the RF Chronotherm
back on the wall holder or table stand.
HC60NG Relay Box Controls Layout
What does it mean when the HC60NG relay box
green LED is ON?
Green LED indicates normal operation of the radio frequency system.
When the green LED is ON the boiler is also ON. When the LED is
OFF the boiler is OFF.
How do I set the time and day?
1. Move the slider to the DAY / position. The time and day marker
will now be flashing on the display indicating they can be changed.
2. Press the + or - button until the correct time is displayed. Each
button press will change the time by one minute and stop the
display from flashing. Holding the button down for a few seconds
will change the time slowly at first, then quickly.
3. Press the DAY 1..7 button until the day marker is positioned under
the correct day (DAY 1 is Monday). Each button press moves the
day marker by one day.
How do I get started with the built-in tempera-
ture program?
Move the slider to the AUTOmatic position.
The Chronotherm will now control your heating using the built-in
temperature program:-
Monday to Friday
Program 1 2 3 4 5 6
Time 06:30 08:00 12:00 14:00 18:00 22:30
Temperature 21°C18°C21°C18°C21°C16°C
Saturday and Sunday
Program 1 2 3 4 5 6
Time 08:00 10:00 12:00 14:00 18:00 23:00
Temperature 21°C21°C21°C21°C21°C16°C
How do I set my own temperature program for
each day of the week?
1. Move the slider to the PROGram position. You will see the first
temperature change time and temperature level for Monday’s
program (the two small arrows are displayed only when the
programmed temperature level is shown). The flashing display
indicates that you can make changes.
DAY /
PROG
AUTO
MAN
OFF
2. Press the + or - button to adjust the first temperature change
time. Holding the button down will change the time quickly. The
change time can be set in 10 minute steps from 03:00 in the
morning. The change time can be adjusted to any time up to 02:50
on the next morning, so you can maintain the evening temperature
after midnight.
(Note: If you are pressing the + button and the display flashes
the next change time number 2, it means the next change time 2
will be pushed forward if you continue to press the + button).
3. Press the TEMPerature or button to adjust the first
temperature level. Holding the button down will change the
temperature quickly. The temperature can be set in 0.5°C steps
from 5°C to 30°C.
4. Press the PROGram 2 button to display the second temperature
change time and temperature level for Monday. Set these by
pressing the + or - button and TEMPerature or button.
5. The remaining temperature changes for Monday can be displayed
by pressing PROGram buttons 3, 4, 5 and 6 and adjusted by
using the + or - button and TEMPerature or button.
(If you don’t want to use all the temperature change times 2, 3, 4,
5 or 6 refer to the next question “What if I don’t want to use all 6
temperature change times?”).
You now have a choice to set the program for the next day:-
6a. Press the COPY DAY button to copy Monday’s program into
Tuesday. To set several days of the week to the same program,
press the COPY DAY button repeatedly.
6b. Press the DAY 1..7 button to step the day marker to Tuesday (Day
2). The program for Tuesday can then be set as described in steps
2 to 5. Programs for Wednesday (Day 3) to Sunday (Day 7) can be
set in the same way, using the DAY 1..7 button.
7. Move the slider to the AUTOmatic position when you have
completed steps 6a or 6b, The Chronotherm will now control the
room temperature to match your program.
What if I don’t want to use all 6 temperature
change times?
The built-in program uses 6 temperature change times as indicated by
the numbers 1, 2, 3, 4, 5 and 6 on the display. With the slider in the
PROGram position, unwanted change times can be deleted by holding
the appropriate PROGram buttons (2, 3, 4, 5 or 6) down for a few
seconds. The change time will be removed and the display will show
dashes instead of a time / temperature display.
Deleted temperature change times can be brought back again by
pressing the appropriate program button (2, 3, 4, 5 or 6) for a few
seconds, with the slider in the PROGram position.
Can I change the programmed temperature for a
short time?
When the slider is in the AUTOmatic position the temperature can be
adjusted temporarily by pressing the TEMPerature or button.
This temperature will return to the programmed value at the next
temperature change time.
How do I check the programmed temperature?
In normal operation the temperature displayed is the actual room
temperature. To check the programmed temperature press the
INFOrmation button and the display will show the programmed
temperature with the two small arrows.
How do I set one temperature for the whole day?
To operate as a simple thermostat with one temperature throughout the
day, move the slider to the MANual position. Adjust the manual
temperature by pressing the TEMPerature
or
button. The
manual temperature can be set anywhere from 5°C to 30°C in 0.5°C
steps.
I am having some friends round for coffee. How
can I extend my heating program for a few hours?
When the slider is in the AUTOmatic position the temperature can be
adjusted temporarily by pressing the (PARTY) button. Set the party
time (1 - 23 hours) by pressing the + or - button. Set the
party
temperature (5°C - 30°C) by pressing the TEMPerature
or
DAY /
PROG
AUTO
MAN
OFF
1234567
1234567
123456
button. The Chronotherm will control to the new temperature for the set
number of hours and then go back to the normal temperature program.
To cancel the PARTY setting press the button a second time or
move the slider.
The button can also be used when you go out (shopping, out with
friends for coffee or to another party!) and want to reduce the tempera-
ture for a few hours to save energy.
I have a day off work tomorrow and I am staying
at home, do I have to re-program the
CM67NG
?
No, with one button press, the
CM67NG will remember that tomor-
row is a day off. Tomorrow, the
CM67NG will control the temperature
using Sunday’s program.
When the slider is in the AUTOmatic position, press the (DAY
OFF) button. A symbol will appear and the day marker for
tomorrow will flash. This indicates that the Sunday temperature
program will be followed tomorrow. Tomorrow the symbol will still
appear but without the flashing day marker, the
CM67NG will control
tomorrow’s temperatures using Sunday’s program.
To cancel tomorrow’s DAY OFF, press the
button twice or move
the slider.
If you have 2 or more days off press the button each night before
going to bed.
If you have a DAY OFF today and want to control the temperature
using Sunday’s program press the button twice.
To cancel any DAY OFF setting, either press the button repeatedly
until the symbol disappears or move the slider.
I am going on holiday for a few days. How do I
save energy but ensure that the house is warm
when I return?
1. Move the slider to the operating position you require on returning
from holiday (AUTOmatic or MANual position)
2. Press the (HOLIDAY) button to display the holiday days counter
and temperature.
3. Press the + or - button to set the holiday time (1 - 99 days). An
extra flashing day marker shows you the holiday return day.
4. Press the TEMPerature or button to set the holiday
temperature (5°C - 30°C).
The unit will control to the new temperature for the set number of days
holiday. At midnight the holiday days counter will be reduced by one
until the selected number of days have passed. The unit will then
return to normal control as set by the MANual or AUTOmatic slider
position.
To cancel the HOLIDAY setting, press the button a second time or
move the slider.
How can I switch the RF Chronotherm off?
Move the slider to the OFF position. The unit has an intelligent built-in
frost protection feature, so that if the temperature falls below 5°C, it will
automatically switch back on to prevent your pipes from freezing.
CM67NG
Controls/Display Layout
The diagram below details the key button functions and display
information.
1234567
1234567
DAY /
PROG
AUTO
MAN
OFF
Display Today
Display Tomorrow
Push button and relay
status LED’s
Battery Low
Indicator
Day Marker Time Display Heat Demand
Indicator
Temperature
Change
Buttons
= increase
= decrease
Information
Enquiry
Button
Temperature
Display
Holiday ButtonDay Off Button
Party Button
Battery
Compartment
Day
Button
Copy Day
Button
Time
Change
Buttons
Setting
Slider
Program
Buttons
NG
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell CM67RF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell CM67RF in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell CM67RF

Honeywell CM67RF User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info