474023
21
Zoom out
Zoom in
Previous page
1/24
Next page
21 68-0134
T8624C,D
TROUBLESHOOTING
THERMOSTAT MOUNTED
INCORRECTLY ON BASE.
BATTERIES ARE INCORRECTLY
INSTALLED.
SYMPTOM POSSIBLE CAUSE ACTION
NO ac POWER TO THERMOSTAT
CHECK POWER TO FURNACE OR AIR CONDITIONER.
ON-OFF SWITCH
FUSE OR CIRCUIT BREAKER
LOOSE 24V CONNECTION
AT THERMOSTAT
AT FURNACE /AIR CONDITIONER
INCORRECT WIRING
CHECK WIRING DIAGRAM
FURNACE OR AIR CONDITIONER
WON'T OPERATE.
NO ac POWER TO THERMOSTAT
CHECK POWER TO FURNACE OR AIR CONDITIONER.
ON-OFF SWITCH
FUSE OR CIRCUIT BREAKER
LOOSE 24V CONNECTION
AT THERMOSTAT
AT FURNACE /AIR CONDITIONER
INCORRECT WIRING
CHECK WIRING DIAGRAM
THERMOSTAT INOPERATIVE CONDUCT SELF-TEST; SEE CHECKOUT.
PRESENT SETTING TOO LOW/HIGH
ADJUST TEMPERATURE BY PUSHING WARMER/
COOLER KEYS.
SYSTEM SWITCH ON THERMOSTAT
IN WRONG POSITION.
RESET THERMOSTAT SYSTEM SWITCH.
WAIT 5 -10 MIN. OR USE SELF-TEST IN THERMOSTAT.
SEE CHECKOUT.
MINIMUM-OFF TIMES IN THERMOSTAT
IN OPERATION ON COOLING
INCORRECT WIRING CHECK CIRCUIT DIAGRAM.
FURNACE OR AIR CONDITIONER
INOPERATIVE
CONSULT FURNACE OR AIR CONDITIONER
INSTRUCTIONS.
PARTIAL DISPLAY INOPERATIVE THERMOSTAT REPLACE THERMOSTAT.
CHECK THAT HEAT OR COOL SYSTEM POWER IS ON.NO POWER TO THERMOSTATNO DISPLAY
SEE INSTALLATION INSTRUCTIONS FOR CORRECT
MOUNTING.
PRESENT SETTING APPEARS
INACCURATE.
THERMOSTAT IS IN RECOVERY
MODE.
NORMAL OPERATION THERMOSTAT TURNS ON
HEATING/COOLING EARLY TO MEET TEMPERATURE
SETTING AT PROGRAMMED TIMES.
RECOVERY CAN BE ENDED BY PUSHING WARMER/
COOLER KEYS.
CANNOT TEMPORARILY OVERRIDE
BOTH HEATING AND COOLING
SETTINGS IN AUTO MODE.
THERMOSTAT TEMPERATURE NEEDS
TO BE ADJUSTED ON A REGULAR
BASIS.
WARMER/COOLER KEYS BEING
USED TO ADJUST TEMPERATURE
REPROGRAM THERMOSTAT TO MAKE PERMANENT
CHANGE IN PROGRAM. WARMER/COOLER KEYS ARE
TEMPORARY UNLESS PERIOD KEY IS PRESSED FIRST.
REMOVE AND REPLACE PER MARKINGS ON THERMOSTAT.
REPLACE BATTERIES.
CHECK PROGRAMMING INSTRUCTIONS FOR CORRECT
PROGRAM SEQUENCE.
REPROGRAM ACCORDING PROGRAMMING INSTRUCTIONS
(MAKE SURE BATTERIES ARE INSTALLED).
PROGRAMMING HAS BEEN LOST
BECAUSE OF A POWER OUTAGE.
DISPLAY FLASHES DURING
OPERATION.
DISPLAY FLASHES WHILE
PROGRAMMING.
IMPROPER PROGRAM SEQUENCE
PROGRAM IS LOST DUE TO POWER
OUTAGE OR DISPLAY GOES BLANK
WHEN POWER IS TURNED OFF.
BATTERIES ARE DEAD.
M5234A
NOT USING PRESENT SETTING KEY.
SET HEATING AND COOLING TEMPERATURES 3 F OR
MORE APART.
O
ROOM TEMPERATURE DISPLAY
IS 32
˚
F.
PRESS AND HOLD DOWN PRESENT SETTING KEY TO
ALTERNATE BETWEEN HEATING AND COOLING SETTINGS.
AUTOMATIC THERMOSTAT HEATING
OR COOLING TEMPERATURE CAN
NOT BE SET CLOSER THAN 3 F.
O
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell Chronotherm III - T8624C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Chronotherm III - T8624C in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info