Manual Honeywell Chronotherm III - 69-0690 (page 21 of 30) (English)

474024

Zoom out

Zoom in

1/30

ANSWERING COMMON QUESTIONS ABOUT THE CHRONOTHERM III THERMOSTAT

Here’s how to override Adaptive Intelligent Recovery

setting:

■ Set the desired WAKE program temperature.

■ Set the WAKE program time 30 to 60 minutes before

the time you normally get up. (You can adjust this

time. If the house reaches the comfort temperature

too early, set the time later; if it reaches the comfort

temperature too late, set the time earlier, but don’t go

beyond 90 minutes.)

■ Set the desired SLEEP program time and tempera-

ture. The SLEEP temperature must not be more than

10 degrees below the comfort setting.

■ Set the RETURN program time to 10 minutes before

your programmed WAKE time.

■ Set the RETURN program temperature the same as

the SLEEP temperature.

■ The LEAVE program remains blank unless you want

a day energy saving period. See page 3.

■ The thermostat will think that it doesn’t need to start

recovery until 10 minutes before your WAKE time. It

will run the furnace constantly until the comfort

temperature is reached.

9. Can I stop the thermostat from bringing the heat

on so early in the morning? How?

T8631A has screws on the back of the thermostat

that will allow you to turn off Adaptive Intelligent

Recovery™.

On the T8631R without the screw to override

Adaptive Intelligent Recovery™, you will only be able

to set one completely automatic energy savings

period; the second period must be ended manually.

Also, since recovery starts at the time you pro-

grammed, the comfort temperature may not be

reached by the desired time.

EXAMPLE:

TEMPERATURE

PERIOD TIME SETTING SETTING

WAKE 5:30 AM 70° F

LEAVE — —

SLEEP 10:00 PM 60° F

RETURN 5:20 AM 60° F

If you want a day program:

■ Set the desired LEAVE time and temperature. The

thermostat will automatically initiate an energy

savings period.

■ The first person home must push the CHANGE

TO LAST PERIOD key to start warming the

house. The furnace will run constantly until the

comfort temperature is reached.

Do you have a heat pump with auxiliary heat?

If so, we don’t recommend overriding Adaptive Intelli-

gent Recovery™ because the amount of expensive

auxiliary heat needed for recovery can cost more than

the energy saved by lowering the temperature.

10. I have a high efficiency furnace and my heat is

short cycling. What can I do?

Some high efficiency furnaces need the cycle rate set

at the Hot Water setting instead of the factory setting

of gas/oil warm air. Turn out the 1A screw with screw

1B left turned in.

Additional Questions? Call Honeywell Consumer

Services: 1-800-468-1502 Monday-Friday, 7:30 a.m. to

5:00 p.m., Central time.

the Thermastat iss completely dark and furnace not working
Submitted on 8-2-2020 at 15:43
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell Chronotherm III - 69-0690 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell Chronotherm III - 69-0690 Manual

Product: