Manual Honeywell chronotherm 4 T8602A (page 2 of 12) (English)

6417

Zoom out

Zoom in

1/12

69-0309—9 2

T8602A,B,C,D AND TS8602A,C Chronotherm

III FUEL SAVER THERMOSTATS

CAUTION

Disconnect power supply to prevent electrical

shock or equipment damage.

Location

Install thermostat and wallplate about 5 ft (1.5m) above the

floor in an area with good air circulation at room

temperature.

Do not install the thermostat where it can be affected by:

— drafts or dead spots behind doors, in corners, or

under cabinets.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall,

behind the thermostat.

If Replacing An Existing Thermostat

Turn off power to the thermostat at the furnace or boiler. A

two-transformer system can require turning off two

switches or disconnects. Remove any existing wallplate or

subbase from the wall. Write down the letter or number on

each wiring terminal, as the wire is removed, to avoid

miswiring later.

If New Installation

Run cable to the hole in the selected wall location, and pull

about 3 in. (76 mm) of wire through the opening. Color-

coded, 18 gauge thermostat cable with at least one

conductor for each wiring terminal is recommended.

Push excess wire back into the hole, and plug the hole

with nonhardening caulk, putty or insulation to prevent

drafts from affecting the thermostat operation.

Mounting Wallplate

Remove thermostat from wallplate. See Fig. 1.

The wallplate does not require leveling for operation, but

for appearance only. The wallplate mounts directly onto

the wall with the screws included. Using the wallplate as a

template, with a pencil, mark two (of three) mounting

screw positions on the wallplate that fit the application. See

Fig. 2. Use a 3/16 in. bit to drill holes for the anchors.

Gently tap anchors into the holes until flush with the wall

surface. Thread wires through the center opening of the

wallplate. Mount the wallplate using the two screws

provided. Gently tighten the screws, level the top surface

of the wallplate, and then securely tighten the screws.

WIRES THROUGH

WALL OPENING

WALL

ANCHORS

(2)

WALLPLATE

MOUNTING

HOLES (3)

MOUNTING

SCREWS (2)

USE TWO MOUNTING HOLES THAT

BEST FIT APPLICATION.

M2917

M2918

Fig. 1. Removing thermostat from wallplate.

Fig. 2. Mounting wallplate on wall.

Wiring

CAUTION

The TS8602A,C can only be used on 750 mV

heating applications. The TS8602A,C will not

function properly on 250 mV, 500 mV or 24 Vac

heating applications.

All wiring must comply with local electrical codes and

ordinances.

Disconnect power before wiring to prevent electrical shock

or equipment damage.

The shape of the terminal barrier permits insertion of

straight or conventional wraparound wiring connections.

Either method is acceptable.

Refer to Fig. 4 through 15 for typical wallplate and

thermostat hookups.

NOTE: • Keep all wiring restricted to the ribbed area

surrounding the terminals (Fig. 3) to assure

thermostat/wallplate contact.

• For single transformer applications, jumper

terminals R and RC for proper operation.

Hi,
I will not be in my house for a week and would like the heating system not to work. Right now it is in Auto, but I do not want the heating to work at all. Can you please advise Submitted on 8-11-2022 at 14:00
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell chronotherm 4 T8602A in the language / languages: English as an attachment in your email.

The manual is 0,16 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honeywell chronotherm 4 T8602A

Honeywell chronotherm 4 T8602A User Manual - English - 16 pages

Honeywell chronotherm 4 T8602A User Manual - Dutch - 57 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Honeywell chronotherm 4 T8602A Manual

Product: