723823

Honeywell 50150 series Manual

5
Zoom out
Zoom in
Previous page
1/24
Next page
5
CAUTION: DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
Do not attempt to wash either the odor reducing pre-filter or the HEPA filter. They
are not washable and washing will damage the filters.
The only two parts requiring any service from you are the odor reducing pre-filter and
the HEPA filter. No tools are needed. To remove or change either filter, disassemble the
unit as shown below:
BEFORE OPERATING THE AIR PURIFIER, MAKE SURE PRE-FILTER IS IN PLACE.
To order replacement pre-filter or filter, refer to the “Accessories and Replacement
Filters” section.
Step 1: Turn the air purifier off and unplug from the wall outlet.
Step 2: To open and gain access to the filter, gently place the air purifier on its side and
unscrew the locking mechanism located on the bottom of the unit (Fig. 2).
Step 3: Remove the base assembly from the air purifier.
Step 4: Remove the filter or filter assembly (consisting of the HEPA filter and pre-filter)
from the internal chamber.
Step 5: If pre-filter is being changed, locate the seam of the pre-filter and carefully
separate the fastener to remove the pre-filter from the HEPA filter (Fig. 3).
Step 6: Discard used pre-filter if necessary. Check the HEPA filter to ensure it is
not too dirty or seems to be clogged. Replace the HEPA filter if necessary.
Step 7: Carefully wrap the pre-filter around the HEPA filter so that the ends meet
(Fig. 4). Fasten the ends together with the fastener provided.
Step 8: Place the whole filter assembly back into the internal chamber. Close the
product by replacing the base and tightening the locking mechanism until snug.
DO NOT OVER-TIGHTEN.
Step 9: Turn the air purifier into an upright position, plug into a wall outlet and it is
then ready for operation.
Do not forget to reset the Intelli-Check™ filter indicator.
Fig. 2 Fig. 4Fig. 3
REMOVING/CHANGING THE FILTERS
50150N_50250S_OM.indd 5 11/18/10 4:37 PM
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honeywell 50150 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honeywell 50150 series in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 4,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info