478015
9
Zoom out
Zoom in
Previous page
1/88
Next page
9 EN
Both sides of 3-tooth and 4-tooth blades can be used.
When one side is worn, the cutting attachment should be turned
over to use the cutting edges on the other side.
Only the bevelled edges of the teeth are to be sharpened.
It is important to keep their profile regular and to avoid incipient
fractures.
All the teeth must be sharpened in the same way.
NOTE:
If the machine vibrates abnormally after sharpening, this
indicates that the blade is unbalanced. In this case, contact your
authorized dealer Honda to have it checked.
CAUTION:
Replace the blade when the wear limit shown in the illustrations
below has been reached.
[A] Unsatisfactory
[1] Incipient fracture
[2] Limit exceeded and
tooth profile irregular
[3] Angles incorrect and unequal
[4] Unsatisfactory cutting profile
[B] Satisfactory
[5] Sharpening limit
ADJUSTING THE CARBURETOR
PROCEDURE
Start the engine and let it warm up to normal operating temperature.
Then turn the idle screw [7] to the right or left to obtain the correct
setting.
NOTE:
When the engine is idling, the cutting attachment must not
rotate.
CHECKING THE SPARK PLUG
1. To reach the spark plug [8],
the top cover must be
removed from the
engine [9]. Use the
hexagonal wrench supplied
to undo the bolt [10].
NOTE:
Hot parts and moving parts (flywheel) are exposed when the
engine top cover is removed. Never use your brush cutter with the
engine cover removed.
2. Remove the cap and unscrew the spark plug using the wrench
supplied.
3. Clean the electrodes with a wire brush [11] to remove carbon
deposits.
4. If the electrodes show signs of wear, replace the spark plug with
a new one with the same characteristics.
5. Check the spark plug gap
with feeler gauges [12].
When adjustment is
required, carefully bend the
side electrode.
6. Reinstall the spark plug and
screw it finger-tight onto its
seat.
7. For new spark plugs,
tighten by an additional 1/2
turn with the spark plug
wrench.When the same
spark plus is installed, 1/8 to 1/4 of a turn is enough.
CAUTION:
If a spark plug is insufficiently tightened, it is liable to heat up and
damage the engine. If the spark plug is overtightened or cross-
threaded, irreparable damage could be caused to the engine
block.
UMK425E1 UMK435E1
Idle speed 3 100 ± 200 rpm.
[2]
[1]
[3]
[4]
[A]
30 mm
[5]
[B]
30°
30°
30°
30°
[7]
SAFETY
B7 C1
[9]
[10]
[8]
0,6-0,7 mm
[11]
[12]
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK435E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK435E in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 19,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK435E

Honda UMK435E User Manual - English - 18 pages

Honda UMK435E User Manual - German - 18 pages

Honda UMK435E User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info