478014
9
Zoom out
Zoom in
Previous page
1/58
Next page
9
SAFETY INSTRUCTIONS
B4.Replace faulty exhaust mufflers.
B5.Each timethe machine isused, beforestarting, perform a generalinspection and check,in particular,all attachments, cutting
assemblies,deflectors and mounting bolts tomake sure that theyare not worn, damagedor loose.Always check that thegas
throttle trigger and the Stop button operate correctly.
B6.Check that the handles andharnessattachmentpoint are correctly positioned andthatthemachine is properly balanced. The
correct positions and adjustments are specified in the section on “Preliminary preparation and checks” in this manual.
B7.Adjust the idle speed so that the cutting attachment stops turning when the throttle control is released.
B8.Install the blade cover on the blade type cutter during removal and installation operations.
- Turn the engine switch to the Stop position and remove the spark plug cap.
- Wear gloves during this operation.
OPERATION
C1.Do not run the engine in a confined space where toxic carbon monoxide fumes may accumulate.
C2.Work by daylight only.
C3.As far as possible, avoid using the machine on wet ground.
C4.When operating the machine, ensure compliance with the safety clearance of the nylon line cutting head with respect to the
harness attachment point.
C5.Walk whenyouusethemachine,neverrun,andstay ina stableposition.Bewareofobstaclessuchas stonesand treestumps
which could trip you.
C6.Tread carefully on slopes. When working on slopes, always proceed crosswise: never straight up and down.
C7.Do not use the machine onslopes that are too steep. It is the operator’s responsibility to assess the potential hazards of the
terrainandtotakeeverynecessaryprecautionforhisorherownsafety.Thisisespeciallyimportantwhenworkingonslopesor
rough, slippery or loose ground.
C8.Never modify the engine settings in such a way that it runs at excessive speeds.
C9.Before starting the engine, make sure there is no-one within 15 metres of the machine, that the cutting attachment is not
touching the ground and that the machine is in a stable position.
C10.Take care when starting the engine. Comply with the safety instructions and stay clear of the cutting attachment.
C11.The engine must be stopped and the spark plug cap removed in the following cases:
- Before performing any servicing action on the cutting system.
- Before cleaning, checking, adjusting or repairing the brushcutter.
- The only adjustments to be carried out with the engine running are carburettor and idle speed adjustments.
- During this operation, make sure the cutting attachment does not strike any object and that the machine is in a stable
position.
- Ifthecuttingattachment strikesanobject,inspectthe cuttingsystemandthetransmission shafttomakesurethey havenot
been damaged. Make any necessary repairs before resuming work with the machine.
- If the brushcutter starts vibrating abnormally, look for the cause of the vibrations immediately and take the necessary
corrective action.
C12.Stop the engine in the following cases:
- Whenever the brushcutter is left unattended.
- Before refilling the fuel tank.
- When moving the machine from one area to another.
MAINTENANCE AND STORAGE
D1.Keep all nuts and bolts securely tightened to ensure safe operation. Regular maintenance is required to ensure safety and
optimal performance.
D2.Do not use the machine with damaged or worn parts. Parts must be replaced, not repaired. Use genuine Honda parts. The
cuttingattachments must alwaysbemarkedwith the manufacturer’sbrand,the reference and themaximumoperating speed.
Parts of inferior quality may damage the machine and compromise operator safety.
D3.Wear heavy gloves when removing and installing the cutting device.
D4.Neverstorethebrushcutterwithfuelinthefueltankinaroomwherefuelvapourcouldbeignitedbyaflame,asparkorasource
of intense heat.
D5.Store in a clean dry room, out of the reach of children.
D6.Let the engine cool down before putting away the machine in any room.
D7.To reduce fire hazards, remove leaves, grass cuttings and excessoil from the brushcutter, particularly from thecooling fins,
the exhaust system and the fuel storage area.
D8.When themachineisstoredor carried,thecuttingblademustalwaysbe coveredbyitstransportguard toavoid anyaccidental
injury.
D9.If the fuel tank has to be drained, this operation must be performed outdoors when the engine is cold.
D10.To protectthe environment, do notdispose of old engineoil orfuel by pouring itdown the drain, in thegutter or on theground.
Your local service station can have oil and fuel safely recycled.
GB
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK431E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK431E in the language / languages: English, German, French as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK431E

Honda UMK431E User Manual - Dutch, Italian, Spanish - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info