478012
35
Zoom out
Zoom in
Previous page
1/58
Next page
35
OPERATION
Replacing the line
1. Lock the nylon line cutting head with a hexagonal wrench [1].
2. Unscrew the nylon line cutting head (by turning in the clockwise direction).
3. Press the lugs [2] located on either side of the head to open it.
4. Extract the reel and remove the rest of the nylon line.
5. Prepare six metres of 2.4 mm diameter line and fold it in half, lengthwise.
6. Place the middle of the line in the notch [3] in the reel and coil the wire by turning in the specified
direction.
7. Secure the ends in the two opposite notches [4] (leaving an excess of 10 cm of line).
8. Reinstall the reel in its place and feed the lines through the two side holes [5].
9. Reinstall the cover.
10. Pull the ends to free them from their notches [4] and screw the head back onto the machine.
CAUTION:
Always use a line of the diameter recommended in the technical specifications.
Poor results would be obtained if the line diameter is too large as this will result in an excessive load
on the engine, so reducing its performance.
Never replace the nylon line with a line of a different
material, such as steel wire.
UTILISATION
Remplacement du fil
1. Bloquer la tête nylon à l’aide de la clé héxagonale [1].
2. Dévisser la tête à fil nylon (sens horaire) .
3. Appuyer sur les languettes [2] situées de chaque côté de la tête pour l’ouvrir.
4. Extraire la bobine et retirer le reste de fil nylon.
5. Préparer 6 mètres de fil de diamètre 2.4 mm et le plier en deux dans la longueur.
6. Placer le milieu du fil dans l’encoche [3] de la bobine et enrouler le fil en tournant dans le sens
indiqué.
7. Coincer les extrémités dans deux encoches opposées [4] (laisser dépasser 10 cm de fil).
8. Replacer la bobine dans son logement, en faisant passer les fils dans les deux orifices
latéraux [5].
9. Remonter le couvercle.
10. Tirersur les extrémitéspour les dégagerdeleur encoche [4]et revisser latête sur lamachine.
PRÉCAUTION :
Toujours utiliser un fil du diamètre recommandé au tableau de spécifications techniques.
Un fil de section trop élevée nuirait aux performances du moteur en générant une charge trop
importante, abaissant ainsi la qualité du travail.
Ne jamais remplacer le fil nylon par un fil d’une autre nature tel que fil de
fer.
F
SAFETY
B8 C11
B8 C11
GB
WARNING :
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK425E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK425E in the language / languages: English, German, French as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK425E

Honda UMK425E User Manual - English - 88 pages

Honda UMK425E User Manual - English - 18 pages

Honda UMK425E User Manual - German - 88 pages

Honda UMK425E User Manual - German - 18 pages

Honda UMK425E User Manual - Dutch - 88 pages

Honda UMK425E User Manual - Dutch - 18 pages

Honda UMK425E User Manual - French, Italian, Spanish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info