478012
23
Zoom out
Zoom in
Previous page
1/58
Next page
23
PRELIMINARY PREPARATION AND CHECKS
BALANCING THE MACHINE
Attach the brush cutter as illustrated [1].
Once the machine is in place, it is essential to check that it is correctly balanced. This check must be
performed with the cutting attachment fitted on the appliance and with the fuel tank half-full.
Adjust the length of the harness so that the cutting attachment is parallel to, and in contact with, the
ground.
When the machine is equipped with a grass-cutting disc, the disc must be fitted with the stabilizer.
Correct balancing is obtained when the stabilizer just gently touches the ground [5].
It must bepossible toraise thecutting attachment off the ground with only a slighteffort onthe handles.
If adjustment is required, move the attachment point [4] forwards if the cutting attachment feels too
heavy or rearwards if it feels too light. Loosen the bolts with the Torx wrench [3] supplied to move the
harness attachment point to the desired position.
CAUTION: (Type U)
Be careful not to pull the throttle cable too tight when moving the handle [2]. Check that the throttle
trigger operates smoothly.
Adjust the position of the loop handle or the bike handle by loosening the four bolts to obtain a
comfortable operating position.
When you have found the ideal position, check the balance again and adjust if necessary.
Then securely tighten the bolts to lock the handle in position.
PRÉPARATION ET VÉRIFICATIONS AVANT UTILISATION
ÉQUILIBRAGE DE LA MACHINE
Accrocher la débroussailleuse comme illustré [1].
Une fois la machine en position, il est impératif de vérifier son équilibrage. Cette vérification doit se
faire avec l’appareil équipé de l’outil de coupe et réservoir de carburant à demi rempli.
Régler la longueur du harnais de telle sorte que l’outil soit parallèle au sol, en contact avec le sol.
Lorsque la machine est équipée d’un disque coupe herbe, ce dernier doit être monté avec le
stabilisateur.
L’équilibrage correct est obtenu lorsque le stabilisateur touche le sol, sans toutefois y reposer avec
une pression trop importante [5].
Un léger effort sur les poignées doit être suffisant pour soulever l’outil du sol. Si un réglage s’avère
nécessaire, déplacer le point d’accrochage [4] vers l’avant si l’outil est trop ‘’lourd’’, ou vers l’arrière
dans le cas contraire : desserrer les vis à l’aide de la clé Torx fournie [3], de façon à déplacer le point
d’accroche à la position souhaitée.
PRÉCAUTION : (type U)
Veiller à ne pas trop tendre le câble des gaz en déplaçant le guidon [2]. Vérifier le libre
fonctionnement de la gâchette d’accélérateur.
Ajuster la position de la poignée simple ou du guidon double en desserrant les 4 vis pour obtenir une
position de travail confortable.
Une fois la position idéale obtenue, vérifier à nouveau l’équilibrage et ajuster le cas échéant.
Serrer ensuite fermement les vis et pour bloquer la poignée en position.
F
GB
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda UMK425E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda UMK425E in the language / languages: English, German, French as an attachment in your email.

The manual is 4,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda UMK425E

Honda UMK425E User Manual - English - 88 pages

Honda UMK425E User Manual - English - 18 pages

Honda UMK425E User Manual - German - 88 pages

Honda UMK425E User Manual - German - 18 pages

Honda UMK425E User Manual - Dutch - 88 pages

Honda UMK425E User Manual - Dutch - 18 pages

Honda UMK425E User Manual - French, Italian, Spanish - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info