625352
19
Zoom out
Zoom in
Previous page
1/42
Next page
19
GONFLEURS
Ne pas utiliser de source à air comprimé (ex. : compresseur) pour gonfler le bateau. Un
surgonflage peut entraîner la rupture des coutures et/ou des parois.
Spécialement étudiés pour gonfler votre bateau à la pression idéale, les gonfleurs livrés avec
votre bateau vous permettent d’éviter tout problème dû à la surpression. Grâce à leur fonction
d’aspiration, ils vous permettent aussi de vider complètement l’air des flotteurs, le bateau peut
alors être plié facilement.
PRÉCAUTION:
Toujours vérifier la pression de gonflage à l’aide du manomètre avant d’embarquer.
1. Visser l'embout fileté du tuyau de raccordement dans la sortie repérée "Normal Use"
(service normal) "IN" (entrée) [2]. Raccorder l'autre embout à la valve du bateau. Utiliser
chacune des valves pour gonfler partiellement la chambre correspondante avant de finir le
gonflage à la pression finale spécifiée. Voir au chapitre Montage la procédure de gonflage
appropriée au modèle de bateau.
2. Visser ensuite l'embout fileté dans la sortie repérée "High Pressure use" (service haute
pression) [4] et terminer le gonflage sur chaque valve de manière à atteindre les pressions
recommandées suivantes :
- Flotteurs : 0,25 bar (Tous types),
- Quilles : 0.35 bar (Types AE2),
- Plancher gonflable : 0,80 bar (Types IE2).
3. Lorsqu'il s'agit de dégonfler le bateau avant son remisage, utiliser l'orifice de dégonflage repéré
"OUT" [3]. Pour dégonfler, visser l'embout fileté du tuyau de raccordement dans l'orifice [3] et
l'autre embout dans la valve du bateau, puis actionner le gonfleur pour évacuer l'air.
[1]
Tuyau de raccordement
[3]
Orifice de dégonflage - "OUT"
[2]
Orifice de gonflage "Normal use" - "IN [4] Orifice de gonflage "High Pressure Use"
FOOT PUMP
Do not use a compressed air source (ex.: air compressor) to inflate the boat.
Overinflation may cause the seams and/or walls themselves to rupture.
Specially designed to inflate your boat to the ideal pressure, the pumps supplied with your boat
allow you to avoid all problems related to excess pressure. The pump’s suction function allows
you to completely deflate the tubes so that the boat can be folded easily.
CAUTION:
Before boarding, always check the inflation pressure using the pressure gauge provided.
1. Screw the threaded end of connecting hose into the outlet marked "Normal Use" "IN" [2].
Fasten the other end to the boat's valve. For each valve, partially inflate each chamber
before finishing inflation to the specified final pressure. Refer to Assembly section for
inflation procedure for your model.
2. Relocate the threaded end into the outlet marked "High Pressure use" [4], finish inflating on
each valve to obtain the following recommended pressures:
-Tubes: 0.25 bar (all types),
- Keels: 0.35 bar (AE2 types),
- Inflatable deck: 0.80 bar (IE2 types)
3. For deflation of boat before storage, use "Deflation orifice - OUT" [3]. To deflate, screw
threaded end of connecting hose into [3] and the other end into the boat's valve, operate
pump to remove air.
[1]
Connecting hose
[3]
Deflation orifice- "OUT"
[2]
Inflation orifice "Normal use" - "IN" [4] Inflation orifice "High Pressure Use"
3 Langues_D-GB-F.fm Page 19 Jeudi, 16. octobre 2008 1:49 13
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda T27 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda T27 in the language / languages: English, German, French as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda T27

Honda T27 User Manual - Dutch, Italian, Spanish - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info