552645
28
Zoom out
Zoom in
Previous page
1/773
Next page
1-23
dummyheaddummyhead
GENERAL INFORMATION
LUBRICATION & SEAL POINTS
ENGINE
MATERIAL LOCATION REMARKS
Liquid sealant
(Three Bond 1207B or
equivalent)
Oil pan mating surface See page 9-12
Right crankcase cover mating surface See page 11-6
CKP sensor wire grommet
Linear solenoid valve wire grommet (NC700XD/SD)
Alternator wire grommet
Alternator cover mating surface See page 13-7
Crankcase mating surface See page 14-28
Molybdenum oil solution
(a mixture of 1/2 engine oil
and 1/2 molybdenum
disulfide grease)
Rocker arm sliding surface
Rocker arm shaft outer surface
Camshaft lobes, journals and thrust surface
Valve stem (valve guide sliding surface) and stem end
Clutch outer guide sliding surface (NC700X/XA/S/SA)
Starter reduction and idle gear shaft outer surface
M3/4, C5, C6 gear (shift fork grooves) (NC700X/XA/S/SA)
M3, M4, C5, C6 gear (shift fork grooves) (NC700XD/SD)
Each transmission spline collar outer surface
Each transmission collar inner and outer surface
Shift fork guide area and guide pin
Shift fork shaft outer surface
Main journal bearing sliding surface
Crankpin bearing sliding surface
Crankshaft thrust surface
Engine oil Oil filter cartridge O-ring
Oil filler cap O-ring
Timing hole cap O-ring
Crankshaft hole cap O-ring
Clutch oil filter cover O-ring (NC700XD/SD)
Oil joint pipe O-ring (NC700XD/SD)
Clutch oil guide collar O-rings (NC700XD/SD)
Oil strainer seal ring
Starter motor O-ring
Injector seal ring
Water pump large O-ring
Valve stem seal
Clutch disc entire surface (NC700X/XA/S/SA)
Clutch lifter rod A sliding surface (NC700X/XA/S/SA)
Clutch lifter rod B sliding surface (NC700X/XA/S/SA)
Mainshaft seal rings (NC700XD/SD)
Starter one-way clutch
Piston sliding surface
Piston ring sliding surface
Piston pin outer surface
Each bearing
Each gear teeth and rotating surface
Each O-ring (except water sealing)
Other rotating area and sliding surface
Multi-purpose grease Each oil seal lips
Locking agent CKP sensor mounting bolt threads Coating width; 6.5 ± 1.0
mm (0.26 ± 0.04 in)
except 2.0 ± 1.0 mm (0.08
± 0.04 in) from tip
Templex N3 grease (ESSO) Electric shift reduction gear teeth and journal (NC700XD/SD) 2 – 4 g (0.07 – 0.14 oz)
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda NC 700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda NC 700 in the language / languages: English as an attachment in your email.

The manual is 19,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info