610602
62
Zoom out
Zoom in
Previous page
1/86
Next page
60
Messages / Resolving problems
Message Cause Solution
Outside loop
The lawnmower exited the boundary
wire.
Move the lawnmower into the work area.
Check the power supply of the docking station.
Check if the boundary wire connectors are
correctly connected.
If the message does not disappear, check if
the boundary wire connectors are correctly
connected, and check if there are no similar
lawnmowers in the area.
If the message still does not disappear, contact
your dealer.
Blade motor
temp high
The temperature of the blade motor is
or exceeds 85°C.
Leave the power ON and the control panel cover
open, and wait 15 to 30 minutes until the message
disappears. If the message does not disappear,
contact your dealer.
Obstruction
detection
An obstruction is being detected, or
the sensor detects something.
Enter the PIN so that the message disappears.
If the message does not disappear, contact your
dealer.
Obstruction
sensor
Obstruction sensor is inactive, or there
is an object interrupting the sensor.
Fully move the main cover in order to check
sensors can be activated.
Shake : Not possible to recover
Turn off : Not possible to recover
If “Obstruction sensor” message remains, check
around and underneath the cover for any objects
like chips, dust or small toys, then remove it, or
contact your dealer.
Excessive tilt
The lawnmower is in an excessively
tilted area.
Place the lawnmower on a at surface, and enter
the PIN so that the message disappears. If the
message does not disappear, contact your dealer.
Mower lifted
The cover has been lifted by
something, e.g. a stone.
Enter the PIN so that the message disappears.
If the cover is heavily damaged or the message
does not disappear, contact your dealer.
Upside down
The lawnmower is upside down. Place the lawnmower on a at surface, and enter
the PIN so that the message disappears. If the
message does not disappear, contact your dealer.
Battery capacity
reduced
The battery does not charge enough.
Increase the remaining capacity of homing. See
“Homing setup” (M page 40). If the message does
not disappear, contact your dealer.
Battery capacity
low
The battery does not charge enough.
No boundary
signal
The lawnmower does not detect the
boundary wire signal.
Check a power supply of docking station. See
“Test start points” (M page 43). If the message
does not disappear, contact your dealer.
Area signal lost
The lawnmower does not detect the
boundary wire signal.
Check if the boundary wire connectors are
correctly connected. If the message does not
disappear, contact your dealer.
Contact your dealer if the following messages have appeared.
Area sensor
Battery Error
Battery temperature
Blade motor
Blade motor blocked
Blade motor relay
Charging control
Clock
Communication Error
Data memory Error
Display Unit Error
Lift sensor
Manual stop
Motor ECU Error
Motor sensor Blade
Motor sensor L
Motor sensor R
Rollover sensor
Tilt sensor
Wheel motor
Wheel motor blocked
Wheel motor relay
Yaw sensor
It may be necessary to exchange the battery. Contact your dealer with the operating history ready (cutting
time, charging time, returning time).
VP7Z.indb 60 2014/12/18 14:26:02
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Miimo HRM 520 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Miimo HRM 520 in the language / languages: English as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Miimo HRM 520

Honda Miimo HRM 520 User Manual - German - 86 pages

Honda Miimo HRM 520 User Manual - Dutch - 86 pages

Honda Miimo HRM 520 User Manual - French - 86 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info