474001
63
Zoom out
Zoom in
Previous page
1/84
Next page
63
MAINTENANCE
BLADE SHARPENING
1. Sharpen the blade cutting edges with a file. File the top side only. Maintain the original bevel
for a fine cutting edge. File both ends evenly to maintain blade balance.
2. After sharpening, test the blade’s balance using a screwdriver as shown. If either side dips
slightly below the horizontal, file that side. Replace the blade if it dips excessively.
CAUTION:
To avoid weakening the blade, causing it to become unbalanced or getting a bad quality of cut,
the blade should be sharpened by competent personnel at your Honda dealer’s.
BLADE REPLACEMENT
CAUTION:
Blade balance is critical to proper mower performance. Replace any blade that is damaged or
out of balance. Use only genuine Honda replacement blades.
BLADE FITTING
1. Clean the dirt and grass from around the blade assembly area.
2. Fit blade [2] using the two bolts [1] and special washers [4] as shown. Fit the special washers
with their concave side facing the blade and the convex side facing the bolts. The blade bolts
are specially designed for this purpose. Do not use other bolts.
ENTRETIEN
AFFÛTAGE DE LA LAME
1. Affûter les bords tranchants de la lame avec une lime. N’affûter que le bord supérieur.
Conserver le biseau d’origine afin d’avoir une arête coupante très acérée. Il est recommandé
d’aiguiser les deux extrémités de manière égale, afin de maintenir l’équilibre de la lame.
2. Après l’affûtage, vérifier l’équilibre de la lame en utilisant un tournevis comme illustré. Si l’un
ou l’autre des bords penche légèrement sous l’horizontale, il faut à nouveau aiguiser ce côté.
PRÉCAUTION :
Afin d’éviter l’affaiblissement des lames, de provoquer leur déséquilibre ou d’obtenir une
coupe de mauvaise qualité, il est préférable de confier l’aiguisage de la lame au personnel
compétent d’un concessionnaire agréé Honda.
REMPLACEMENT DE LA LAME
PRÉCAUTION :
L’équilibre de la lame est essentiel pour obtenir de bonnes performances de coupe. Il faut
donc changer toute lame qui serait endommagée ou dont l’équilibre ne peut être rétabli.
N’utiliser qu’une lame de rechange d’origine Honda.
REMONTAGE DE LA LAME
1. Nettoyer la saleté et l’herbe se trouvant autour de la zone de montage de la lame.
2. Installer la lame [2] en utilisant les 2 vis [1] et les rondelles spéciales [4] comme illustré. Les
vis de lames sont spécialement conçues pour cet usage. Ne pas utiliser d’autres vis.
SAFETY
SECURITE
GB
F
B3 C18 D7 D8
D9
B3 C18 D7 D8
D9
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRB425C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRB425C in the language / languages: English, German, French as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRB425C

Honda HRB425C User Manual - Dutch, Italian, Spanish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info