473997
69
Zoom out
Zoom in
Previous page
1/92
Next page
MAINTENANCE
BLADE FITTING
1. Clean the dirt and grass from around the blade assembly area.
2. Install the flange of the bearing shim against the bearing (HRA536 - HRH536).
3. Fit blade [2] using the two bolts [3] and special washers [1] as shown. Fit the special washers
with their convex side, marked OUT, facing the bolts.
CAUTION:
Viewed from below, the blade turns counterclockwise. When reinstalling, place the blade so
its cutting edges face this direction of rotation (punched reference oriented against blade
holder).
The blade bolts are specially designed for this purpose. Do not use other screws.
4. Retighten the blade bolts using a torque wrench. Use a wood block to stop the blade rotating
when tightening the screws.
Blade bolt tightening torque: 5 to 6 kg.m (from 49 to 59 N.m)
CAUTION:
If you do not have the required sharpening equipment or a torque wrench [5], ask your
approved HONDA dealer to tighten the blade bolts for you before you use the mower.
If the blade bolts are too tight or too slack, they may break or unscrew.
GB
ENTRETIEN
MONTAGE DE LA LAME
1. Nettoyer la saleté et lherbe se trouvant autour de la zone de montage de la lame.
2. Installer la cale de roulement avec sa colerette positionnée contre le roulement (HRA536 -
HRH536).
3. Installer la lame [2] en utilisant les deux vis [3] et les rondelles spéciales [1] comme illustré. Monter
les rondelles spéciales avec le côté convexe marqué OUTtourné vers les vis.
PRÉCAUTION :
Vue comme ci-dessus, la lame tourne dans le sens inverse des aiguilles dune montre. Lors
du remontage, placer la lame de manière à ce que les arêtes tranchantes soient face à la
direction de rotation (référence gravée tournée contre le support de lame).
Les vis de lames sont spécialement conçues pour cet usage. Ne pas utiliser dautres vis que
celles dorigine.
4. Resserrer les vis de lame avec une clé dynamométrique [5]. Utiliser un bloc de bois pour
empêcher la lame de tourner lors du resserrage des vis.
Couple de serrage pour les vis de lame : de 5 à 6 kg.m (de 49 à 59 N.m)
PRÉCAUTION :
Si vous ne disposez pas de léquipement nécessaire à laffûtage et de clé dynamométrique [5],
faites réaliser laffûtage et resserrer les vis de lame par un concessionnaire HONDA agréé.
Des vis de lame trop ou trop peu serrées peuvent se briser ou se dévisser.
F
69
69


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda HRA536 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda HRA536 in the language / languages: English, German, French as an attachment in your email.

The manual is 2,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda HRA536

Honda HRA536 User Manual - Dutch, Italian, Spanish - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info