13145
10
Zoom out
Zoom in
Previous page
1/12
Next page
10
Emission Control System Information
Source of Emissions
The combustion process produces carbon monoxide, oxides of
nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of
nitrogen is very important because, under certain conditions, they
react to form photochemical smog when subjected to sunlight. Carbon
monoxide does not react in the same way, but it is toxic.
Honda utilizes lean carburetor settings and other systems to reduce
the emissions of carbon monoxide, oxides of nitrogen, and
hydrocarbons.
The U.S. and California Clean Air Acts
EPA and California regulations require all manufacturers to furnish
written instructions describing the operation and maintenance of
emission control systems.
The following instructions and procedures must be followed in order to
keep the emissions from your Honda engine within the emission
standards.
Tampering and Altering
Tampering with or altering the emission control system may increase
emissions beyond the legal limit. Among those acts that constitute
tampering are:
Removal or alteration of any part of the intake, fuel, or exhaust
systems.
Altering or defeating the governor linkage or speed-adjusting
mechanism to cause the engine to operate outside its design
parameters.
Problems That May Affect Emissions
If you are aware of any of the following symptoms, have your engine
inspected and repaired by your servicing dealer.
Hard starting or stalling after starting.
Rough idle.
Misfiring or backfiring under load.
Afterburning (backfiring).
Black exhaust smoke or high fuel consumption.
Replacement Parts
The emission control systems on your Honda engine were designed,
built, and certified to conform with EPA and California emission
regulations. We recommend the use of genuine Honda parts
whenever you have maintenance done. These original-design
replacement parts are manufactured to the same standards as the
original parts, so you can be confident of their performance. The use of
replacement parts that are not of the original design and quality may
impair the effectiveness of your emission control system.
A manufacturer of an aftermarket part assumes the responsibility that
the part will not adversely affect emission performance. The
manufacturer or rebuilder of the part must certify that use of the part
will not result in a failure of the engine to comply with emission
regulations.
Maintenance
Follow the maintenance schedule on page 4. Remember that this
schedule is based on the assumption that your machine will be used
for its designed purpose. Sustained high-load or high-temperature
operation, or use in unusually wet or dusty conditions, will require
more frequent service.
Air Index
An Air Index Information hang tag/label is applied to engines certified
to an emission durability time period in accordance with the
requirements of the California Air Resources Board.
The bar graph is intended to provide you, our customer, the ability to
compare the emissions performance of available engines. The lower
the Air Index, the less pollution.
The durability description is intended to provide you with information
relating the engine’s emission durability period. The descriptive term
indicates the useful life period for the engine’s emission control
system. See your Emission Control System Warranty (page 11) for
additional information.
The Air Index Information hang tag/label must remain on the engine
until it is sold. Remove the hang tag before operating the engine.
Specifications
Tuneup Specifications
CONSUMER INFORMATION
Honda Publications
These publications will give you additional information for maintaining
and repairing your engine.You may order them from an authorized
Honda engine servicing dealer.
Descriptive Term Applicable to Emissions Durability Period
Moderate 50 hours (0–65 cc)
125 hours (greater than 65 cc)
Intermediate 125 hours (0–65 cc)
250 hours (greater than 65 cc)
Extended 300 hours (0–65 cc)
500 hours (greater than 65 cc)
Type
N1 N2 A1 A2
Length x Width
x Height
in (mm)
15.6 x 13.2 x 13.4
(395 x 335 x 340)
15.6 x 13.2 x 12.8
(395 x 335 x 325)
15.6 x 13.2 x 13.4
(395 x 335 x 340)
15.6 x 13.2 x 12.8
(395 x 335 x 325)
Dry weight lb
(kg)
25.6 (11.5) 25.6 (11.5) 25.1 (11.3) 25.1 (11.3)
Engine type 4-stroke, overhead valve, single cylinder
Displacement
[Bore x Stroke]
8.2 cu in (135 cm
3
)
[2.7 x 1.8 in (68 x 45 mm)]
Max. output 5.0 bhp at 3,600 rpm
Max. torque 7.6 ft-lb (1.05 kg/m) at 2,500 rpm
Fuel
consumption
0.514 lb/hph (313 g/kWh)
Cooling
system
Forced air
Lubrication
systems
Forced splash
Ignition system CDI
PTO shaft
rotation
Counterclockwise
ITEM SPECIFICATION MAINTENANCE
Spark plug gap 0.028 – 0.031 in (0.7 – 0.8 mm) Refer to page 6.
Valve clearance (cold)
IN: 0.15 ± 0.04 mm
EX: 0.20 ± 0.04 mm
See your authorized
Honda dealer
Other specifications No other adjustments needed.
Shop Manual This manual covers complete maintenance and overhaul
procedures. It is intended to be used by a skilled
technician.
Parts Catalog This manual provides complete, illustrated parts lists.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines GXV140 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines GXV140 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Honda Engines GXV140

Honda Honda Engines GXV140 User Manual - German - 16 pages

Honda Honda Engines GXV140 Quick start guide - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info