13129
14
Zoom out
Zoom in
Previous page
1/60
Next page
−−
Storage Precautions
TRANSPORTING
Removal from Storage
Engine Oil
Draining the Fuel Tank and Carburetor
ENGLISH
DRAIN BOLT
FUEL VALVE LEVER
GASKET
O-RING
ON
Align notch on pulley
with hole at top of cover.
SEDIMENT CUP
14
If your engine will be stored with gasoline in the fuel tank and
carburetor, it is important to reduce the hazard of gasoline vapor
ignition. Select a well-ventilated storage area away from any
appliance that operates with a flame, such as a furnace, water
heater, or clothes dryer. Also avoid any area with a spark-
producing electric motor, or where power tools are operated.
If possible, avoid storage areas with high humidity, because that
promotes rust and corrosion.
Keep the engine level in storage. Tilting can cause fuel or oil
leakage.
With the engine and exhaust system cool, cover the engine to
keep out dust. A hot engine and exhaust system can ignite or melt
some materials. Do not use sheet plastic as a dust cover. A
nonporous cover will trap moisture around the engine, promoting
rust and corrosion.
Gasoline is highly flammable and explosive, and you
can be burned or seriously injured when handling
fuel.
Stop engine and keep heat, sparks, and flame away.
Wipe up spills immediately.
Place an approved gasoline container below the carburetor, and
use a funnel to avoid spilling fuel.
If the cylinder was coated with oil during storage preparation, the
engine will smoke briefly at startup. This is normal.
Check your engine as described in the
BEFORE OPERATION
CHECKS
section of this manual (see page ).
If equipped with a battery for electric starter types, recharge the
battery once a month while the engine is in storage.
This will help to extend the service life of the battery.
Handle fuel only outdoors.
Remove the carburetor drain bolt and gasket. Remove the
sediment cup and O-ring, then move the fuel valve lever to the
ON position.
After all the fuel has drained into the container, reinstall the
drain bolt, gasket, sediment cup and O-ring. Tighten the drain
bolt and sediment cup securely.
Change the engine oil (see page ).
Pour a tablespoon 5 10 cm
(5 10 cc) of clean engine oil into
the cylinder.
Pull the starter rope several times to distribute the oil in the
cylinder.
Reinstall the spark plug.
Pull the starter rope slowly until resistance is felt and the notch
on the starter pulley aligns with the hole at the top of the recoil
starter cover. This will close the valves so moisture cannot enter
the engine cylinder. Return the starter rope gently.
Remove the spark plug (see page ). If the engine has been running, allow it to cool for at least 15
minutes before loading the engine-powered equipment on the
transport vehicle. A hot engine and exhaust system can burn you
and can ignite some materials.
If the fuel was drained during storage preparation, fill the tank with
fresh gasoline. If you keep a container of gasoline for refueling, be
sure it contains only fresh gasoline. Gasoline oxidizes and
deteriorates over time, causing hard starting.
Keep the engine level when transporting to reduce the possibility
of fuel leakage. Turn the fuel valve to the OFF position (see
page ).
2.
1.
3.
1.
2.
3.
4.
5.
6.
3
9
12
5
05/02/21 18:32:00 32Z5F600_014
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines GX390 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines GX390 in the language / languages: French, Spanish as an attachment in your email.

The manual is 7,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Honda Engines GX390

Honda Honda Engines GX390 User Manual - English - 38 pages

Honda Honda Engines GX390 User Manual - German, Dutch, Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info