13129
3
Zoom out
Zoom in
Previous page
1/60
Next page
BEFORE OPERATION CHECKSFEATURES
IS YOUR ENGINE READY TO GO?
Check the General Condition of the Engine
Check the Engine
OIL ALERT SYSTEM (applicable types)
CIRCUIT PROTECTOR (applicable types)
ENGLISH
CIRCUIT
PROTECTOR
ON
OFF
3
For your safety, and to maximize the service life of your
equipment, it is very important to take a few moments before you
operate the engine to check its condition. Be sure to take care of
any problem you find, or have your servicing dealer correct it,
before you operate the engine.
Improperly maintaining this engine, or failure to
correct a problem before operation, can cause a
malfunction in which you can be seriously hurt or
killed.
Always perform a pre-operation inspection before
each operation, and correct any problem.
Before beginning your pre-operation checks, be sure the engine is
level and the engine switch is in the OFF position.
Always check the following items before you start the engine:
Look around and underneath the engine for signs of oil or
gasoline leaks.
Remove any excessive dirt or debris, especially around the
muffler and recoil starter.
Look for signs of damage.
Check that all shields and covers are in place, and all nuts, bolts,
and screws are tightened.
Check the fuel level (see page ). Starting with a full tank will
help to eliminate or reduce operating interruptions for refueling.
Check the engine oil level (see page ). Running the engine
with a low oil level can cause engine damage.
The Oil Alert system (applicable types) will automatically stop
the engine before the oil level falls below safe limits. However,
to avoid the inconvenience of an unexpected shutdown, always
check the engine oil level before startup.
Check the reduction case oil level on applicable types (see page
). Oil is essential to reduction case operation and long life.
Check the air filter element (see page ). A dirty air filter
element will restrict air flow to the carburetor, reducing engine
performance.
Check the equipment powered by this engine.
Review the instructions provided with the equipment powered
by this engine for any precautions and procedures that should
be followed before engine startup.
Push the circuit protector button
to reset.
The green indicator inside the
circuit protector will pop out to
show that the circuit protector has
switched off. If this occurs,
determine the cause of the
problem, and correct it before
resetting the circuit protector.
The circuit protector protects the
battery charging circuit. A short
circuit, or a battery connected
with reverse polarity, will trip the
circuit breaker.
If the engine stops and will not restart, check the engine oil level
(see page ) before troubleshooting in other areas.
The Oil Alert system is designed to prevent engine damage
caused by an insufficient amount of oil in the crankcase. Before
the oil level in the crankcase can fall below a safe limit, the Oil
Alert system will automatically stop the engine (the engine switch
will remain in the ON position).
1.
2.
3.
4.
5.
1.
2.
3.
4.
8
9
9
10
9
‘‘Oil Alert is a registered trademark in the United States’’
07/06/08 09:47:45 32Z5F600_003
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines GX390 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines GX390 in the language / languages: French, Spanish as an attachment in your email.

The manual is 7,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Honda Engines GX390

Honda Honda Engines GX390 User Manual - English - 38 pages

Honda Honda Engines GX390 User Manual - German, Dutch, Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info