13107
10
Zoom out
Zoom in
Previous page
1/60
Next page
ENGLISH
6 : 1 Reduction Case 6 : 1 Reduction Case
2 : 1 Reduction Case With Centrifugal Clutch
Oil Change
AIR CLEANER
Inspection
UPPER
LIMIT
LOWER LIMIT
FILLER CAP/DIPSTICK
DRAIN PLUG
OIL-LEVEL-CHECK BOLT
FILLER BOLTOIL LEVEL
OIL-LEVEL-CHECK BOLT
FILLER BOLT
OIL LEVEL
10
Remove the oil-level-check bolt
and washer, and see whether the
oil level is at the edge of the bolt
hole. Place a suitable container below the reduction case to catch the
used oil, then remove the filler bolt, oil-level-check bolt and
washers.
With the engine in a level position, fill oil until it starts to flow
out the check bolt hole with the recommended oil (see page ).
Reinstall the oil-level-check bolt, filler bolt and new washers,
and tighten them securely.
Drain the used oil while the engine is warm. Warm oil drains
quickly and completely.
Drain the used oil completely into the container by tipping the
engine toward the oil-level-check bolt hole.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash or pour it on the ground
or down a drain.
Running the engine with a low reduction case oil level can cause
reduction case damage.
If the oil level is below the check
bolt hole, remove the filler bolt
and washer. Add oil until it starts
to flow out the check bolt hole
with the recommended oil (see
page ).
Screw in the filler cap/dipstick securely.
Running the engine with a low reduction case oil level can cause
reduction case damage.
Reduction case oil capacity: 0.50 (0.53 US qt , 0.44 Imp qt)
With the engine in a level position, fill to the upper limit mark on
the dipstick with the recommended oil (see page ). To check
the oil level, insert and remove the dipstick without screwing it
into the filler hole.
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash or pour it on the ground
or down a drain.
Allow the used oil to drain completely, then reinstall the drain
plug and a new washer, and tighten it securely.
Place a suitable container below the reduction case to catch the
used oil, then remove the oil filler cap/dipstick, the drain plug
and washer.
Drain the used oil while the engine is warm. Warm oil drains
quickly and completely.
Install the oil-level-check bolt,
filler bolt and washers. Tighten
them securely.
A dirty air cleaner will restrict air flow to the carburetor, reducing
engine performance. If you operate the engine in very dusty areas,
clean the air filter more often than specified in the MAINTENANCE
SCHEDULE.
Operating the engine without an air filter, or with a damaged air
filter, will allow dirt to enter the engine, causing rapid engine wear.
This type of damage is not covered by the
Distributor’s Limited
Warranty.
Remove the air cleaner cover and inspect the filter elements.
Clean or replace dirty filter elements. Always replace damaged
filter elements. If equipped with an oil-bath air cleaner, also check
the oil level.
Refer to pages for instructions that apply to the air cleaner
and filter for your engine type.
1.
2.
3.
4.
1.
2.
3.
1.
2.
3.
4.
9
9
9
1211
05/06/17 17:25:07 32Z4F601_010
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines GX200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines GX200 in the language / languages: English as an attachment in your email.

The manual is 8,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Honda Engines GX200

Honda Honda Engines GX200 User Manual - German, Dutch - 60 pages

Honda Honda Engines GX200 User Manual - Dutch - 33 pages

Honda Honda Engines GX200 User Manual - Italian - 60 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info