13077
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
AIR CLEANER
A dirty air cleaner will restrict air flow to the carburetor and cause poor
engine performance. Inspect the filter each time the engine is
operated. You will need to clean the filter more frequently if you
operate the engine in very dusty areas.
NOTICE
Operating the engine without an air filter, or with a damaged filter, will
allow dirt to enter the engine, causing rapid engine wear. This type of
damage is not covered under the Distributor’s Limited Warranty (see
page 11).
Inspection
1. Press the latch tabs on the top of the air cleaner cover, and remove
the cover.
2. Remove the foam element from the air cleaner cover.
3. Remove the screen grid from the paper element.
4. Check both elements to be sure they are clean and in good
condition.
5. Reinstall the screen grid over the paper element. Make sure that
the screen grid completely surrounds the paper pleats.
6. Reinstall the foam element in the air cleaner cover.
7. Set the paper element and screen grid in the air cleaner body then
install the air cleaner cover.
Cleaning
1. Paper Element: Tap the paper element several times on a hard
surface to remove dirt, or blow compressed air [not exceeding 30
psi (207 kPa, 2.1 kg/cm²)] through the filter from the clean side that
faces the engine. Never try to brush off dirt. Brushing will force dirt
into the fibers.
2. Foam Element: Wash the element in a solution of household
detergent and warm water, then rinse thoroughly, or wash in
nonflammable or high flash point solvent. Allow the element to dry
thoroughly.
Soak the element in clean engine oil and squeeze out the excess
oil. The engine will smoke during initial start-up if too much oil is left
in the foam, or the oil could saturate the paper element making the
engine inoperable.
3. Wipe dirt from the air cleaner body and cover using a moist rag. Be
careful to prevent dirt from entering the air duct that leads to the
carburetor.
SPARK PLUG
Recommended Spark Plug: NGK BPR6ES
The recommended spark plug is the correct heat range for normal
engine operating temperatures.
NOTICE
Incorrect spark plugs can cause engine damage.
For good performance, the
spark plug must be properly
gapped and free of deposits.
1. Disconnect the cap from
the spark plug, and
remove any dirt from the
spark plug area.
2. Use the proper size spark
plug wrench to remove the
spark plug.
3. Inspect the spark plug. Replace it if
damaged, badly fouled, if the
sealing washer is in poor condition,
or if the electrode is worn.
4. Measure the electrode gap with a
suitable gauge. The correct gap is
0.028 - 0.031 in (0.70 - 0.80 mm). If
adjustment is needed, correct the
gap by carefully bending the side
electrode.
5. Install the spark plug carefully, by
hand, to avoid cross-threading.
6. After the spark plug is seated, tighten with the proper size spark
plug wrench to compress the washer.
7. When installing a new spark plug, tighten 1/2 turn after the spark
plug seats to compress the washer.
8. When reinstalling the original spark plug, tighten 1/8 - 1/4 turn after
the spark plug seats to compress the washer.
NOTICE
A loose spark plug can become very hot and can damage the
engine. Overtightening the spark plug can damage the threads in
the cylinder head.
9. Attach the spark plug cap to the spark plug.
AIR
DUCT
AIR CLEANER
BODY
PAPER
FILTER
AIR
CLEANER
COVER
LATCH TABS
TAB (2)
FOAM
ELEMENT
GRID
SPARK PLUG
WRENCH
0.028 ~ 0.031 in
(0.70 ~ 0.80 mm)
SEALING
WASHER
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda Honda Engines GS190 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda Honda Engines GS190 in the language / languages: English as an attachment in your email.

The manual is 0,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda Honda Engines GS190

Honda Honda Engines GS190 User Manual - English - 40 pages

Honda Honda Engines GS190 User Manual - German, Dutch - 32 pages

Honda Honda Engines GS190 User Manual - French - 40 pages

Honda Honda Engines GS190 User Manual - Italian - 32 pages

Honda Honda Engines GS190 User Manual - Spanish - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info