580732
10
Zoom out
Zoom in
Previous page
1/16
Next page
Cleaning
1.Remove the air cleaner cover and foam filter element, as
described in the inspection procedure.
2.Remove the paper element from the air cleaner base.
3.Paper element:
Tap the element several times on a hard surface to remove
excess dirt, or blow compressed air [not exceeding 207 kPa (30
psi)] through the filter from the wire screen side. Never try to
brush off dirt; brushing will force dirt into the fibers. Replace the
paper element if it is excessively dirty.
4.Foam element
Clean in warm, soapy water or nonflammable solvent, rinse and
dry thoroughly. Do not use gasoline as a cleaning solvent,
because that would create a risk of fire or explosion.
For GXV160K1 only:
Dip the element in clean engine oil, then squeeze out all excess oil.
NOTE
Excess oil will restrict air flow through the foam filter and may
transfer to the paper filter, soaking and clogging it. (GXV160K1)
5.Wipe dirt from the air cleaner base and cover using a moist rag.
Be careful to prevent dirt from entering the air duct that leads to
the carburetor.
6.Reinstall the air cleaner elements, and make sure both elements
are correctly positioned. Install the air cleaner cover and tighten
the wing bolt securely (1for GXV140, 2 for GXV160K1).
Spark Plug
Recommended Spark Plugs:
NGK: BPR5ES - NIPPONDENSO Co., Ltd.: W16EPR-U
The recommended spark plug is the correct heat range for normal
engine operating temperatures. The engine can be damaged if a
spark plug with an incorrect heat range is used.
For good performance, the spark plug must be correctly gapped
and free of deposits.
1.Disconnect the cap (1) from the
spark plug (2), and remove any
dirt from the spark plug area.
2.Use the correct size plug
wrench (3) to remove the spark
plug.
3.Inspect the spark plug.
Replace it if damaged, badly
fouled, if the sealing washer is in
poor condition, or if the
electrode is worn. If the spark
plug is to be reused, clean it with
a wire brush.
4.Measure the electrode gap with
a suitable gauge. The correct
gap is 0.7 - 0.8 mm
(0.028 - 0.031 in). If adjustment
is needed, correct the gap by
carefully bending the side
electrode.
ATTENTION traits de coupes ancrés à un cadre automatique.
Positions : Gauche : 4.1 Haut : 3
2221
(2)
(1)
(3)
0,7 ~ 0,8 mm
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Honda GXV160K1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Honda GXV160K1 in the language / languages: English as an attachment in your email.

The manual is 0,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Honda GXV160K1

Honda GXV160K1 User Manual - German - 16 pages

Honda GXV160K1 User Manual - Dutch - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info