518473

Homedics WFL-ROC-3 Manual

3
Zoom out
Zoom in
Previous page
1/29
Next page
54
GB
GB
ASSEMBLY AND INSTRUCTIONS FOR USE :
1. Unpack the product. Wipe off dust with a damp cloth.
2. Familiarize yourself with the pump. The pump speed is controlled by the switch located at the
front of the pump. The speed is indicated by a plus (+) and minus (-) sign. To increase the
speed, move the switch slowly downward in the direction of the plus sign. At its highest speed
level, the switch will cease to move any further. To decrease the pump speed, move the switch
upward toward the minus sign. Similarly, at its lowest speed, the switch will cease to move any
further (Fig 9). NOTE: It is recommended the pump be set at its highest speed during
assembly and later adjusted to a lower setting if desired. Be sure to unplug the pump before
adjusting the speed setting.
3. Lead the cord through the cord slot on the bottom of the Base (A). This will ensure that the
unit is balanced when placed on a flat surface. Attach the A/C adaptor jack to the base
power cord. DO NOT plug into outlet at this time. See Figure 1.
4. Slide the waterproof light into the socket clip attached at the inner side of the slate holder (C).
5. Attach the large end of the tube to the connector located under the Top Slate (B). See figure 1.
6. Take the tube on the bottom side of the Top Slate (B) and place it through the Slate Holder
(C). Place this all the way so that you can see the tube through the opening on the back of
the Slate Holder (C). See Figure 2. NOTE: When placing the top slate (B) onto the slate
holder (C) be sure to line up the top slate notches with the slate holder cut-outs.
7. Place the Slate Holder (C) with the Top Slate attached (B) evenly across the Base (A).
Connect the small end of the tube to the pump. See Figures 3 and 4. NOTE: When placing
slate holder (C) onto Base (A), be sure to line up the opening of slate holder (C) with the
notches on Base (A).
8. Insert the Slate (D) into the “U” shaped slot (lowest) on the back of the Slate Holder (C), to
cover the pump. Insert Slates (E, F, G) into the Slate Holder as illustrated in the diagram. See
Figure 5. NOTE: This is the slate positioning that we recommend. The slates are
interchangeable and will fit into any of the slots on the Slate Holder. The slates can be
arranged differently - by pulling the slates in or out - the fountain will produce different water
patterns and sounds.
9. Arrange the stones provided onto the base and slates. See Figure 6.
10.Look through the opening on the back of the slate holder and fill the entire bottom of the
base, up to the bottom Slate Holder, with clean water. Water should be visible through the
back opening in the slate holder but should not be rising above the bottom of the Slate
Holder.
11.Plug the cord into 230V mains outlet. The fountain is controlled by the switch located on the
power cord. If pump doesn’t operate, rotate in-line switch once to turn “on” and once more to
turn “off”. NOTE: Ensure that the electrical cord loops below the electrical outlet to form a ‘Drip
Loop’ (Fig. 7). This will prevent water from running down the cord into the electrical outlet.
Stones
Switch
Adaptor
Cord Slot
Waterproof light
(A) Base
Slate (G)
Slate (F)
Slate (E)
(D) U-Shaped Slate
Slate Holder
(B) Top Slate
Light Socket Clip (C)
Pump
Tube
Figure 1 Figure 2
C
B
Figure 3
A
B
C
Cut-outs
Notches
Opening
Figure 6
Figure 4
Figure 5
A
B
C
D
E
F
G
Opening
Notches
Drip Loop
Figure 7
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Homedics WFL-ROC-3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Homedics WFL-ROC-3 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info