518474

Homedics WFL-ROC-2 Manual

12
Zoom out
Zoom in
Previous page
1/29
Next page
2322
ES
ES
MONTAJE E INSTRUCCIONES DE UTILIZACIÓN :
1. Desempaquete el producto. Limpie el polvo con un paño húmedo.
2. Familiarícese con la bomba. La velocidad de la bomba es controlada por el interruptor
situado en la parte delantera de la bomba. La velocidad es indicada por un signo más (+) y
un signo menos (-). Para aumentar la velocidad, mueva lentamente el interruptor hacia abajo
en la dirección del signo más.. Oirá un clic cada vez que el interruptor pase a otro nivel de
velocidad. A su nivel máximo de velocidad, el interruptor dejará de moverse. Para reducir la
velocidad de la bomba, gire el interruptor hacia arriba en el sentido del signo menos. De
forma similar, a su velocidad mínima, el interruptor dejará de moverse. (Fig. 9). NOTA: Se
recomienda que la bomba se ponga a su velocidad máxima durante el montaje y que
posteriormente se ponga a un ajuste más bajo si se desea. Asegúrese de desenchufar la
bomba antes de establecer el ajuste de velocidad.
3. Haga pasar el cable a través de la ranura correspondiente situada en la parte inferior de la
base (A). Esto hará que la unidad esté equilibrada cuando se coloque sobre una superficie
plana. Conecte el adaptador de CA en el cable de alimentación de la base. NO enchufe el
aparato en el tomacorriente en esta fase. Ver Figura 1.
4. Coloque la luz a prueba de agua en el clip del enchufe montado en el lado interno del
portapizarras (C).
5. Conecte el extremo grande del tubo al conector situado debajo de la pizarra superior (B).
Ver Figura 1.
6. Take the tube on the bottom side of the Top Slate (B) and place it through the Slate Holder
(C). Place this all the way so that you can see the tube through the opening on the back of
the Slate Holder (C). See Figure 2. NOTE: When placing the top slate (B) onto the slate
holder (C) be sure to line up the top slate notches with the slate holder cut-outs.
7. Place the Slate Holder (C) with the Top Slate attached (B) evenly across the Base (A).
Connect the small end of the tube to the pump. See Figures 3 and 4. NOTE: When placing
slate holder (C) onto Base (A), be sure to line up the opening of slate holder (C) with the
notches on Base (A).
8. Insert the Slate (D) into the “U” shaped slot (lowest) on the back of the Slate Holder (C), to
cover the pump. Insert Slates (E, F, G) into the Slate Holder as illustrated in the diagram. See
Figure 5. NOTE: This is the slate positioning that we recommend. The slates are
interchangeable and will fit into any of the slots on the Slate Holder. The slates can be
arranged differently - by pulling the slates in or out - the fountain will produce different water
patterns and sounds.
9. Arrange the stones provided onto the base and slates. See Figure 6.
10 Look through the opening on the back of the slate holder and fill the entire bottom of the
base, up to the bottom Slate Holder, with clean water. Water should be visible through the
back opening in the slate holder but should not be rising above the bottom of the
Slate Holder.
11.Plug the cord into 230V mains outlet. The fountain is controlled by the switch located on the
power cord. If pump doesn’t operate, rotate in-line switch once to turn “on” and once more to
turn “off”. NOTE: Ensure that the electrical cord loops below the electrical outlet to form a ‘Drip
Loop’ (Fig. 7). This will prevent water from running down the cord into the electrical outlet.
Piedras
Interruptor
Adaptador
Ranura de cable
Luz a prueba de agua
(A) Base
Pizarra (G)
Pizarra (F)
Pizarra (E)
(D) Pizarra en forma
de “U”
Portapizarras
((B) Pizarra superior
Light Socket Clip (C)
Bomba
Tubo
Figura 1 Figura 2
C
B
Figura 3
A
B
C
Recortes
Ranuras
Apertura
Figura 6
Figura 4
Figura 5
A
B
C
D
E
F
G
Apertura
Ranuras
Bucle de goteo
Figura 7
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Homedics WFL-ROC-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Homedics WFL-ROC-2 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info