30184
7
Zoom out
Zoom in
Previous page
1/8
Next page
7
6 NEON T ransmitter Option Installation Directions.
Trainer
switch
Trainer
jack
Screws
ATV Board Installation
1. Open the case as instructed on page 3 and disconnect the throttle
s witch harness plug from the main board.
2. Disconnect the pow er from the radio b y removing the battery holder
or unplugging and removing the Nicad battery pack.
3. Remo v e the four scre ws holding in the large brown PC board in the
illustration.
4. Without unplugging anything on the board, you should be able to shift
the board up out of the wa y about 1 inch.
Note: slide the white wire ne xt to the antenna screw post out of the slot.
5. Pop the "cov er" out from the three small holes and place the ATV board
on the two screw posts. Secure the board with the two supplied screws , be sure to tighten the screws up snug.
6. Taking care to route the wires under the boards as much as possible , re-install the f our screws holding down
the large brown PC board.
7. Slide the white wire next to the antenna screw post into the slot and out of the wa y of the antenna as it is reinserted.
8. Re-install the battery.
9. Plug the throttle back in.
10. Taking care not to pinch any wires, slide the top of the case half's together then snap the bottom together .
Reinstall the antenna, antenna bezel, crystal and the lower case tabs.
11. All done? Range check y our radio and go fly!
Trainer P ort and Switch Installation
1. Open the case as instructed on page 3 and disconnect the throttle
s witch harness plug from the main board.
2. Disconnect the power from the radio by remo ving the battery holder
or unplugging and removing the Nicad battery pack.
3. Twist out and remov e the plastic cov er from the back side of the case
so the trainer plug can be accessed after the case is closed.
Clean up the edges with a hobby knif e .
4. Plug the 6 wire plug into the port marked "trainer" and route the
wires so they will not be pinched when the case is re-assembled.
5. Pop the plastic plug out from the top right of the Tx case and
install the switch b y removing both small nuts, sliding the s witch
up through the hole and securing both nuts so the top nut "jams"
the bottom one tight. Taking care to orient the switch so when the Tx is resting in your hand in the flying position,
the s witch is pulled tow ards you and snaps back a wa y from y ou when released.
6. Route the wires so they will not be pinched when the case is re-assembled.
7. Place the plug port PC board on the f our screw posts and use the f our screws to secure it.
8. Re-install the battery.
9. Plug the throttle back in.
10. Taking care not to pinch any wires, slide the top of the case half's together then snap the bottom together .
Reinstall the antenna, antenna bezel, crystal and the lower case tabs.
11. All done? Range chec k your radio and go fly!
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Hitec NEON_SS_FM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Hitec NEON_SS_FM in the language / languages: English as an attachment in your email.

The manual is 0,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info